The disposal price has been reduced! (Member discounts are not applicable) 2024/5/24 sales price 29,800 yen ※1 wooden horn is compatible not only with FOSTEX drivers, but also with JBL 1-inch drivers (stop 3 points). It is a horn characterized by a broad sound unique to wood horns, which is different from metal horns (Takahashi Nobuyuki)
Main specifications: cutoff frequency 420 Hz throat 2.54 cm birch wood parallel plywood W444 × H90 × D293 mm 3.1 kg (actual measurement)
The price has been reduced! 2024/5/25 sales price 69,800 yen Manufacturer maintained! Rotel's pre-main amplifier. The successor to the company's RA-1062. A full-scale design that uses WBT terminals and other parts that cost more than the price. The unobtrusive and refreshing sound quality is compatible with a wide variety of genres. As for the exterior, there is a feeling of use such as scratches and dullness on the top plate. Serial 867-3031022 (Tomonori Asaine)
Maintenance information: Maintained on 2024.5.24 (volume rotation improvement implemented. Speaker relay contacts have deteriorated (both A/B), B has been replaced, and A improvements have been implemented. (Other maintenance carried out)
Accessories: remote control power cord
Main specifications: 75W+75W with MM input W431 x H99 x D358 mm 8.7 kg
※Since it is a commercial device, there is no problem with the as-is operation, but since there is no guarantee, it is inexpensive. The sound quality is clean, fresh, and light, and the sound is firm and crisp. The sound development is such that the image that comes to mind when using the word YAMAHA for commercial use fits perfectly. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.21 Operation confirmed
Accessories: copy of instruction manual, power cord
Main specifications: stereo output 105W+105W (4Ω) 100W+100W (8Ω) bridge output 210W (8Ω) frequency characteristics 20Hz-50kHz damping factor 200 input terminal XLR, phone, output terminal 5WAY binding post power consumption 150W W480 x H880 x D456mm 12 kg
This is a boost transformer (Type L version) for FR low impedance MC cartridges. There is a sense of clarity, and the clean, straight sound is attractive. There are small wounds and dullness (Oikawa Tetsuji)
Maintenance information: 2024.5.26 Operation confirmed
Accessories: none
Main specifications: input impedance 3 ohms or less, output impedance 47 to 50 kΩ, W158 x H60 x D120 mm, 2.1 kg
*Currently sold. The output has been changed to an RCA female terminal. FR MC boost transformer using a toroidal core. Create a natural sound that makes it easy to understand the characteristics of cartridges. In addition to switching the impedance of 10 to 30 ohms, there is also a bypass position, so it is compatible with various cartridges without taking up much space. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.21 Operation confirmed
Accessories: copy of instruction manual, connection cable
Main specifications: impedance 10 ohm/30 ohm/PASS playback frequency band 20 Hz to 30 kHz W64 x H64 x D105 mm approx. 455 g
What an analog cleaning type LP cleaner that is cleaned by manually rotating the disc in a circle. A brush is attached to the inside of the main unit to scrape out dirt from the grooves. There are hardships, such as being hard to spin, getting your hands dirty, etc., but it seems to be a fun cleaning job. The drying stand is missing. We cannot guarantee the quality of the included cleaning solution (Murakoshi Yoichi)
Accessories: special cleaning solution, label protect cover, filter funnel, original box, instruction manual (German)
Main specifications: W336 x H182 x D84 mm 2.2 kg
115V specification A power amplifier that is supported by a heavyweight power transformer and reproduces tight low frequency reproduction with good visibility. It shows high cost performance that exceeds size and price. There are small scratches on the exterior (Hiura Katsuji)
Maintenance information: 2024.5.26 sound output confirmed
Accessories: instruction manual, power cable, original box
Main specifications: 45W+45W (8Ω) 75W+75W (4Ω) W483 × H51 × D295mm 7.5 kg
115V specification A power amplifier that is supported by a heavyweight power transformer and reproduces tight low frequency reproduction with good visibility. It shows high cost performance that exceeds size and price. There are small scratches on the exterior (Hiura Katsuji)
Maintenance information: 2024.5.26 sound output confirmed
Accessories: instruction manual, power cable, original box
Main specifications: 45W+45W (8Ω) 75W+75W (4Ω) W483 × H51 × D295mm 7.5 kg
*Currently sold. The 13 cm cone-shaped woofer is equipped with an OMF diaphragm made of natural materials, and is specially designed, such as using a German WIMA capacitor for the network, so you can enjoy solid sound with high cost performance. You can see the exterior, dullness, dirt, abrasions, etc. and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.25 Operation confirmed
Accessories: saran net
Main specifications: anti-magnetic design 2-way bass reflex woofer 13 cmOMF diaphragm tweeter 2.5 cm soft dome rated impedance 4 Ω maximum input 70 W rated sensitivity level 85 dB/w/m rated frequency range 50 Hz to 35 kHz W170 x H295 x D232 mm 3.8 kg
* There are adhesive marks on the main body, the tweeter is dead, etc., so it is inexpensive and is currently sold. If you're a Technics fan, you should try the SB-7000 at least once! It is made with a linear phase design and expresses excellent directivity. Although it is flat and has a wide range, it is highly efficient, so it can handle a full range of genres regardless of the amplifier. The exterior has adhesive marks, dirt, and small scratches. Shipping costs will be estimated separately (Oikawa Tetsuji)
Maintenance information: 2024.5.28 Operation confirmed
Accessories: none
Main specifications: 3-way bass reflex 6Ω 93dB linear phase speaker system W480 x H845 x D410 mm 36 kg
*The remote control is out of stock, so it is cheap and is currently sold. An entry model with excellent cost performance. Since it comes with a phono circuit, you can also enjoy records. The sound quality is stable in both digital and analog. There are small wounds and dullness (Oikawa Tetsuji)
Maintenance information: 2024.5.28 Operation confirmed
Accessories: none
Main specifications: 50W+50W (8Ω) line input 4 phono 1 system (MM) with pre-out terminal W434 x H121 x D308 mm 7.1 kg
※Some glass doors are out of stock. Audio rack with casters of unknown model number and details. The shelves are adjustable with dowels. Overall, there is a feeling of use such as scratches, dirt, and seal marks. Shipping costs will be estimated separately (Daiki Goto)
Accessories: none
Main specifications: W1130 x H1010 x D470 mm Approximate weight 60 kg
※Since it is cheap, it will be handed over as is. DSD compatible network audio player. Equipped with WIFI, the D/A converter is compatible with DSD 5.6 MHz and 192 kHz/32 bit, the same as those used in super audio CD players. It is a model with high cost performance. Recommended for those getting started with network audio. There is a line wound. The remote control is out of stock (Oikawa Tetsuji)
Maintenance information: 2024.5.28 Operation confirmed
Accessories: instruction manual, power cable
Main specifications: DSD (2.8 MHz/5.6 MHz) AIFF (192 kHz/24 bit) AIFF, WAV, FLAC (192 kHz/24 bit) Apple Lossless (96 kHz/24 bit) wireless LAN standard IEEE 802.11b, IEEE 802.11g, IEEE 802.11n compliant W434 x H73 x D297 mm 2.9 kg
※The current situation is that there is a slight tear on the cone paper on one side and a dent in the center cap. Fostex 10cm full range. A speaker unit developed as a successor to the FE103en. A three-dimensional sound field expression has been achieved while keeping the bright and clear tone characteristic of the series intact. In addition to the appearance described above, dullness and a feeling of use can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.5.26 Operation confirmed
Accessories: instruction manual, original box, gasket
Main specifications: 8Ω FS to 22kHz 88.5 dB W106 × H47 × D106 mm 566 g
*The woofer edge is deformed, the center cap is dented, there is an ATT crack, and there are footprints on the top plate, etc., so it is inexpensive and is sold as is. A floor-type speaker with a porous metal cone that realizes all-metal in the entire band. From the unit to the enclosure, this is a masterpiece that incorporates technology and cost as if Otto's intention were shown. The rich, natural sound is attractive. The enclosure also has scratches, chipped corners, etc. (Oikawa Tetsuji)
Maintenance information: 2024.5.29 Operation confirmed
Accessories: none
Main specifications: 3 way 3 speakers 8Ω 93dB W450 × H910 × D430 mm 51 kg
*Currently sold. A small speaker with a 16.5 cm woofer. This is a high cost performance speaker that allows you to listen to rich musical sounds that are beyond its size. The full expressive power of the mid-range is attractive. The exterior is good with no conspicuous scratches. Serial 37866 (Yonejima Satoshi)
Maintenance information: 2024.5.30 good sweep test
Accessories: saran net
Main specifications: 2 way impedance 8 ohms efficiency 90 dB playback frequency band 43 to 21,000 Hz W227 x H360 x D230 mm 7 kg
The price has been reduced. 2024/5/30 sales price 128,000 yen Maintained! This is a Dynaco tubular control amplifier. It is an amplifier where you can enjoy the warm and comfortable sound unique to vintage. While the microwave feel is moderate, the nostalgic sound with an emphasis on atmosphere has a unique, hard-to-get flavor. There is a feeling of use such as rust stains on the top and sides, and rust etc. on the knobs (Murakoshi Yoichi)
Maintenance information: 2024.5.29 maintenance (12AX7, 2000 μF electrolytic capacitor, 1 μF replacement, 1/4 W resistance added as a measure to improve switching noise, vacuum tube socket and RCA jack caulking repair, parts check including block capacitors, and operation check with AC 100 to 117 V)
Accessories: none
Main specifications: vacuum tube 12 AX7 x 4, 12 x 4 line input 5 systems phono 1 system (mm) 1 pre-out system W385 x H134 x D230 mm 7 kg
Speaker cable 3.0 m/4.3 m pair end end uses a μ-conductor with unique processing applied to the PC-OCC conductor for the purpose of reproducing sound with good sharpness, and it is a cable with excellent cost performance that also achieves delicate high-frequency reproduction (Fujisawa Yukishi)
Maintenance information: 2024.5.31 continuity confirmed
Accessories: No accessories
It hasn't been in stock in a long time! Accuphase Premium Cartridges Using a sapphire tube cantilever, the sound is straightforward with no specific sound, almost no distortion, and a perfect sense of range. Now it's a manufacturer that pushes ahead with the cutting edge of digital audio, but it's a cartridge where you can once again feel the high level of analog audio technology (Yamato Yuki)
Maintenance information: 2024.5.31 operation confirmed
Accessories: The original box needle cover is missing
Main specifications: MC type output voltage 0.18 mV needle pressure 1.5 to 2.5 g optimal 2 g impedance 4 ohms line contact needle
DENON analog player. It is a model that is easy to use and has excellent cost performance. The phono cable is detachable and can be replaced with a cable of your choice. This model is also suitable for introductory use. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Asaine Tomoho)
Maintenance information: 2024.6.1 operation confirmed
Accessories: instruction manual cartridge, EP adapter, subweight
Main specifications: quartz servo type direct drive speed 33 1/3 rpm, 45 rpm static balance S-shaped pipe arm needle pressure adjustment range 0 to 4.0 g compatible cartridge weight 14.0 to 20.0 g W450 x H170 x D370 mm 10.1 kg
Maintained! ONKYO premain amplifier with high cost performance. A non-feedback power amplifier is used, and the power supply transformer is of high quality and carefully crafted. The power amplifier direct position allows direct input to the power amplifier via volume only. The exterior is dull. Serial 4604014114 (Yonejima Satoshi)
Maintenance information: 2024.2.15 Maintained (input selector, direct switch, etc. Switch disassemble contacts, polish contacts and apply contact cleaner. Main amplifier circuit input circuit soldering correction)
Accessories: instruction manual
Main specifications: 100W+100W (8Ω) PHONO input 1 system (MM/ MC switching) W445 x H165 x D434 mm 18.0 kg
Maintained! The thickness of the mid range and the thickness of the low range are an exciting masterpiece pre-main. The special phono part uses a transformer for built-in MC boosting. Compared to lower models, it combines the politeness of being able to enjoy classical music. Appearance, dullness, abrasions, and a feeling of use can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.6.2 maintained (tone switch and other switches dismantled and polished, coated with grease (subsonic, loudness, muting, input selector, reckout), output relay, headphone relay replacement, main amplifier transistor, adjustment volume replacement, solder and board repair, balance volume replacement, each volume, switch cleaning, interior and exterior inspection cleaning, adjustment, operation confirmation)
Accessories: copy of instruction manual
Main specifications: 130W+130W (8Ω) PHONO (MM/MC) 2 systems W460 x H160 x D444 mm 18 kg
Orthophone 95th anniversary special limited set with shell An aluminum headshell SH-4 special limited-edition color red type is attached to the popular 2M Red MM cartridge. This is a high cost performance entry model MM cartridge that is clear, has good sound separation, and fits well with modern sources. *Since there is a crack on the needle cover side, it cannot be fixed to the main body. (MURAKOSHI Yoichi)
Maintenance information: 2024.6.2 sound output confirmed
Accessories: instruction manual, original box, needle cover (broken claws), brush, screws, shell
Main specifications: [2M RED] MM type 5.5 mV 20 to 22,000 Hz 47 ohms suitable needle pressure 1.8 g dead weight 7.2 g [SH4R] gold plated terminal body material aluminum self weight 9.3 g (excluding mounting screws)
115V specification A power amplifier that is supported by a heavyweight power transformer and reproduces tight low frequency reproduction with good visibility. It shows high cost performance that exceeds size and price. Serial 2172380ZGD00103 (Fujisawa Yukishi)
Maintenance information: 2024.6.2 operation confirmed
Accessories: power cord
Main specifications: 45W+45W (8Ω) 75W+75W (4Ω) W483 × H51 × D295mm 7.5 kg
2.0m PSE standard power cable with a diameter of 11 mm with an OFC conductor held tightly with a PVC sheath. It is a cable with excellent cost performance, with rhodium plating on both the connector and plug (Murakoshi Yoichi)
Maintenance information: 2024.6.2 continuity confirmed
Accessories: none
Luxman's current phono equalizer that uses a non-feedback CR amplifier circuit using an all-stage vacuum tube has arrived! Using vacuum tubes, 4 independent Super Permaloy MC boost transformers and 4 output transformers are mounted on the left, right, and low/high, respectively. It is a model that emphasizes sound quality, using a VU meter and OFC, which are fun to look at. It is one that can be controlled in a variety of ways. There are small wounds and dullness (Sasaki Shota)
Maintenance information: 2024.6.3 operation confirmed
Accessories: original box, manual, power cable
Main specifications: circuit method: SRPP, terminal cathode follower, non-feedback CR type equalizer (RIAA) vacuum tube: ECC83 x 4, ECC82 x 2, EZ81 x 1 input sensitivity (1 kHz, when gain is switched 36 dB): MM 4mV, MC high 0.44mV, MC low 0.18mV input impedance: mm30kΩ to 100kΩ (variable), MC high 40Ω, MC low 2.5Ω gain (1kHz, when gain is switched at 36 dB): mm36dB, MC High55dB, MC Low63dB S/N ratio mm76dB, MC High75dB, MC Low74dB W440 x H92 x D397mm weight 12.5 kg