New exterior maintenance has been carried out! In 2024/12, we completed our refreshment maintenance, which focuses on creating a new dust cover, disassembling and cleaning the arm, and increasing motor bearing grease! A record player with high cost performance by inheriting technology obtained with the GT-2000. It conveys all the goodness of analog discs where power and subtlety coexist and you can enjoy rich overtones. The exterior has a feeling of use such as dullness and scratches. Serial 04274 (Yamato Yuki)
Maintenance information: 2026.2.5 maintained (exterior repair/side painting on one side)
2024.12.21 Maintained (motor bearing cleaning, lubrication arm lifter disassembly, cleaning, grease up, tone arm disassembly, cleaning, grease up), brand new replacement operation, SW dismantling, polishing, cleaning, grease up. Turntable rotation speed confirmation, arm operation, needle pressure confirmation, exterior cleaning, sound output test, other operation confirmation)
Accessories: copy of instruction manual
Main specifications: Statically balanced S-shaped arm mounted applicable cartridge 3G to 12g direct drive drive quartz PLL servo control DC coreless hole motor turntable 36 cm aluminum die cast W532 x H220 x D388 mm 22 kg
Sansui's rare MM type. You can expect it as a collector's item or as a highly versatile piece. The exterior is generally dull and has small scratches (Matsumoto Tsuyoshi)
Maintenance information: 2026.2.5 sound output confirmed
Accessories: none
Main specifications: Appropriate needle pressure 2.0 to 2.5 g dead weight 6 g
Yamaha VM type cartridges. The needle is slightly bent. The sound quality is well-balanced and suitable as an introduction to analog. The exterior is dull and has a feeling of use (Matsumoto Tsuyoshi)
Maintenance information: 2026.2.5 operation confirmed
Accessories: none
Main specifications: VM type round needle, suitable needle pressure 2.0g
*Currently sold. Remote control is missing. It has a high signal-to-noise ratio and low THD value, and you can enjoy clear sound quality with little noise regardless of genre. In addition to paint peeling on the exterior and inside of the tray, you can also see a feeling of use such as dullness and scuffs. serial VT8AB01856 (Yamato Yuki)
Maintenance information: 2025.9.16 Operation confirmed
Accessories: power cable
Main specifications: frequency characteristics 2 Hz to 20 kHz dynamic range 100 dB or more (EIAJ) S/N ratio 120 dB or more (EIAJ) headphone output level maximum 15 mw/32 Ω (variable) dimensions W430 x H114 x D290 mm weight 4.0 kg
It also has tracing power, and the brightness and richness of the low frequencies is attractive. The exterior is dull and has a feeling of use. Serial 3538266 (Matsumoto Tsuyoshi)
Maintenance information: 2026.2.5 operation confirmed
Accessories: none
This is a thick 5mm acrylic dust cover. It was custom-ordered by the previous owner for the MC275, but it seems that it can be used for others as long as the size fits. The exterior has some scuffs over time (Yamato Yuki)
Accessories: none
Main specifications: dimensions W430 x H250 mm x D350 mm 3.2 kg
Unspecified plastic headshell. The lead wire is missing. It is simple and seems to be easy to use. The exterior is dull and has a feeling of use (Matsumoto Tsuyoshi)
Maintenance information: 2026.2.5 continuity confirmed
Accessories: none
Main specifications: dead weight 6 g
Unspecified headshell. It is simple and seems to be easy to use. The exterior is dull and has a feeling of use (Matsumoto Tsuyoshi)
Maintenance information: 2026.2.5 continuity confirmed
Accessories: none
Main specifications: 10 g dead weight
Sansui's black shell. Its own weight is also light and easy to adjust. The cartridge mounting screw hole is oval and the overhang can be adjusted. The exterior is dull and has a feeling of use (Matsumoto Tsuyoshi)
Maintenance information: 2026.2.5 continuity confirmed
Accessories: none
Main specifications: dead weight 5 g
Unspecified headshell. It is simple and seems to be easy to use. The exterior is dull and has a feeling of use (Matsumoto Tsuyoshi)
Maintenance information: 2026.2.5 continuity confirmed
Accessories: none
Main specifications: dead weight 9 g
Yamaha perforated lightweight shell. It is lightweight and strong due to aluminum press processing. The exterior is dull and has a feeling of use (Matsumoto Tsuyoshi)
Maintenance information: 2026.2.5 continuity confirmed
Accessories: none
Main specifications: aluminum stamping dead weight 9g
This is a Sony headshell that seems to be made of die-cast aluminum. It is sturdy and well-built. The exterior is dull and has a feeling of use (Matsumoto Tsuyoshi)
Maintenance information: 2026.2.5 continuity confirmed
Accessories: none
Main specifications: dead weight 15 g
Maintained! JBL mid-size studio monitor speaker A 3-way specification that combines an ultra-high range compression driver. It features clear and powerful sound quality full of transparency. You can enjoy the new-generation JBL sound with a wide range. The exterior is generally in good condition due to maintenance. Serial HA1108-IG0034108/HA1108-IG0034080 (Tomo Asaine)
Maintenance information: 2026.2.3 maintained (175Nd-3 maintenance (porcelain circuit total decomposition, iron powder removal, neodymium magnet and center yoke adjustment adhesive) exterior repair/polishing/painting, front baffle touch-up saran net cleaning/tacker reinforcement, dowel repair woofer cleaning/edge coating ATT cleaning unit detachable)
Accessories: instruction manual, saran net jumper plate, original box
Main specifications: 3-way bookshelf type frequency band 38 Hz to 45 kHz 6 Ω 91 dB W400 x H635 x D335 mm 32.3 kg
The disposal price has been reduced! (Member prices are not applicable) 2026/1/17 sales price 1,280,000 yen Full maintenance was completed in 2024/12 after spending plenty of time on the unit, network, and exterior! This is an AUTOGRAPH with an HPD385 mounted in a genuine TEAC box. I am overwhelmed by the majestic sense of scale and profound and vivid sound image expressed by the low range backroad horn and the mid to low range front short horn, and it also has a good supple and beautiful tone that cannot be obtained with TANNOY in recent years. The exterior is in a state where there is a slight feeling of use over time, but it is generally beautiful depending on maintenance (Yamato Yuki)
Maintenance information: 2024.12.15 Maintained (exterior repair/polishing/clear finish, front and rear baffle repair/paint maintenance: net cleaning/repasting, fraying repair/frame repair. Unit maintenance: low pass side edge exchange, magnetic circuit gap cleaning center adjustment, fastener polishing, high frequency side magnetic circuit gap cleaning center adjustment. Network maintenance: frequency characteristic check, ATT cleaning, faston terminal replacement, 4-pin terminal/terminal cleaning)
Accessories: saran net
Main specifications: 2-way, 1 speaker, all-horn system, corner type usage unit, 15 inch (38 cm), HPD385 impedance 8 ohms, W1070 x H1530 x D660 mm, 78 kg/book
The disposal price has been reduced (member prices are not applicable) 2026/1/24 sales price 1,180,00 yen, opened goods with a 5-year manufacturer's warranty! First arrival in gloss black color! Current Martin Logan electrostatic speaker, a model that combines an electrostatic panel and a 20cm dual aluminum cone woofer. It has the technical elements of the ESL series, and you can enjoy the overwhelming sound field and three-dimensional effect unique to this shape. The vividness of the classical style has a tonal appeal not found in the dynamic type. The exterior is also good with no noticeable scratches. Serial ALQ7395820M06/ALQ7395821M06 (Asaine Tomoho)
Maintenance information: 2026.1.24 Operation confirmed
Accessories: original box, instruction manual, warranty card, power cable, spike
Main specifications: frequency characteristics 34 to 23,000 Hz, recommended amplifier output, 50 to 400 W, horizontal directivity, 30° sensitivity, 90 dB impedance, 4 ohms, crossover frequency, 380 Hz, W 264 x H1520 x D646 mm, weight 35.4 kg
Everything from the exterior to the unit network has been fully maintained in 2020! A system equipped with the famous Monitor GOLD machine in an original sealed enclosure. The good sound of acoustic instruments and small-group classics is still attractive enough. The beauty of the sound, which can be said to be the origin of European beautiful tone speakers, is exceptional. The exterior is in beautiful condition due to maintenance. *The speaker terminals have been changed to be compatible with banana plugs. Serial 112309, 112706 (Yamato Yuki)
Maintenance information: 2020.9.2 Maintained (the rod-shaped contacts on one side of the output terminal were replaced, and the contacts were polished and cleaned. Input terminal replacement, input terminal panel repair with adhesive. ATT (SW type) contact cleaning. Electrolytic capacitor replacement. Frequency characteristic measurement check (~ 42 kHz). Check the input/output waveform and balance, and check the sound output. Unit maintenance (magnetic circuit rust removal/slit cleaning/center adjustment for both low and high frequencies) unit detachable exterior repair/polishing/clear finish. Rear baffle paint. Saran net cleaning/retensioning)
Accessories: none
Main specifications: Coaxial 2-way sealed speaker system unit 10 inch MONITOR GOLD coaxial 2-way playback frequency band 25 Hz to 20 kHz maximum input 15 W input impedance 8 Ω crossover frequency 1 kHz dimensions W380 x H583 x D 240 mm weight 13 kg
A special package model designed to commemorate Rega's 50th anniversary. It is a product that includes the walnut model (not sold separately) of the Planar 3 MK2, which is representative of the company's analog player, and the power supply unit - Neo PSU. The compact design, which is excellent as an interior, is also attractive. There are light scratches on the dust cover on the exterior. Serial 004891 (Takahashi Nobuyuki)
Maintenance information: 2026.2.4 operation confirmed
Accessories: original instruction manual box
Main specifications: drive system: weight of cartridge that can be mounted on a belt drive: 4.5 g to 8.5 g Exact: mm type impedance 47 kΩ needle pressure 1.75 g W447 x H360 x D117 mm mass 6.0 kg Neo PSU: W180 x H50 x D155 mm mass 0.6 kg
A bookshelf speaker equipped with a JET Folded Ribbon Tweeter. Resonance is suppressed by adopting the same enclosure as the advanced model. The outline is also clearly depicted, and the clear bass is attractive. As for the exterior, there are line scratches on the sides and small scratches on the lower part of the front, but the impression is that there is not much feeling of use. Serial 32302E001431/3230E001432 (Yamato Yuki)
Maintenance information: 2026.2.4 sound output checked (good sweep test)
Accessories: unit cover jumper plate
Main specifications: 2 way 2 speakers bass reflex impedance 6 ohms playback frequency band 46 Hz to 30 kHz output sound pressure level 85 dB size W210 x H321 x D213 mm mass 6.7 kg
A speaker that uses an SMC (soft magnetic compound) magnetic circuit that is also installed in the EPICON series. 2-way configuration with 26mm tweeter+120mm wood fiber cone woofer Although it is small, you can fully enjoy Dali. The exterior is generally in good condition, but there are scratches on the front panel. Serial 1975574/1975574 (Yamato Yuki)
Maintenance information: 2026.2.4 sound output checked (good sweep test)
Accessories: saran net
Main specifications: 2 way 2 speakers 4 ohms 86 dB W152 x H261 x D231 mm 4.5 kg
*Currently sold. Although it is in the low price range, it has a glossy, stretchy sound like England and goes well with small amplifiers. If you pair it with Arkham and the musical Fidelity, you can enjoy an even more atmospheric sound. There is a feeling of use on the exterior, such as corner marks and line scratches. Serial 023442/023443 (Takahashi Nobuyuki)
Maintenance information: 2026.2.4 operation confirmed (good sweep test)
Accessories: saran net
Main specifications: frequency band 48Hz to 20kHz 89dB 8Ω W253 × H497 × D230 mm 7.5 kg
*Currently sold. Entry class for Yamaha CD players. It has a simple design dedicated to pure audio playback and is equipped with a USB input terminal compatible with direct mode and WAV/FLAC. The exterior is dull and there are scratches on the top plate. Serial Z031035VX (Takahashi Nobuyuki)
Maintenance information: 2026.2.4 operation confirmed
Accessories: Remote control instruction manual, power cable, connection cable, original box
Main specifications: USB input ~ 96kHz 24bit W435 × H87 × D260 mm 3.5 kg
Speaker stand from Hayami Industries. It is a large type with a top plate size of 350 mm wide x 280 mm deep. The direction of the top plate can be changed vertically or horizontally to match the speaker. The mounting direction of the pillar can also be changed according to the atmosphere of the speaker to be installed (Yamato Yuki)
Accessories: none
Main specifications: W450 x H400 x D380 mm approx. 7 kg/bottle
The shell that came with 70s SONY record players. The ease of use is attractive. There is a feeling of use on the exterior such as scratches and dullness (Takahashi Nobuyuki)
Maintenance information: 2026.2.4 continuity confirmed
Accessories: none
Main specifications: dead weight 10.8 g
A Sony headshell with a unique design. The cartridge holder is in the shape of a slide bar, making it easy to adjust the overhang. The exterior is dull and has a feeling of use (Takahashi Nobuyuki)
Main specifications: high-rigidity die-cast aluminum, 10.5g dead weight
Sony die-cast aluminum shell While it is sturdy, it has a smart design and is easy to use. The exterior is dull and has a feeling of use (Takahashi Nobuyuki)
Main specifications: die-cast aluminum, 10.5g dead weight
A shell that was standard equipment on Sony's mid-level players. It is an aluminum body that moderately suppresses sounds. You can see a feeling of use such as dullness on the exterior (Takahashi Nobuyuki)
Maintenance information: 2026.2.4 continuity confirmed
Accessories: none
Main specifications: aluminum stamping dead weight 8g
Maintenance has been completed, such as dismantling and cleaning the main volume and disassembling and polishing of each switch! The final model of the Sansui α507 series. This is an entry class for the NRA series, which is highly transparent and crisp. This is an attractive car with a good balance and luster. You can see a feeling of use, such as appearance, dullness, small scratches, etc. Serial 609114393 (Tomonori Asaine)
Maintenance information: 2026.2.2 maintained (phono circuit part IC capacitor replacement main volume disassembly cleaning input selector processor MMMC switch disassembly polishing protector part capacitor replacement output relay replacement other volume cleaning interior and exterior inspection cleaning operation confirmation)
Accessories: instruction manual
Main specifications: 60W+60W (8Ω) line input 5 systems phono 1 system (MM/MC switching) W432 x H165 x D450 mm 15.5 kg
Speaker cable, 2.6 m pair, Y lug on one side, O-terminal end, highly conductive tinned copper, 2-core twisted pair structure, flat, with little coloring. There is a feeling of use on the exterior such as yellowing and dirt (Takahashi Nobuyuki)
Maintenance information: 2026.2.3 continuity confirmed
Accessories: none
The speaker cable with unknown details uses a 1.6m peeritz wire and is relatively thick, but it is a soft cable that is easy to handle. There is a feeling of use on the exterior, such as dullness and dirt (Takahashi Nobuyuki)
Maintenance information: 2026.2.3 continuity confirmed
Accessories: none
The 1.5m pair terminal of the phone-RCA cable is a standard BELDEN line cable that clearly shows the outline of the REAN (NEUTRIK) terminal sound while having a firm thickness, especially in the mid to low range. The exterior has a feeling of use such as dullness and dirt (Takahashi Nobuyuki)
Maintenance information: 2026.2.3 continuity confirmed
Accessories: none