It smells like an air freshener, and since ATT has cracks, it is cheap, and is currently discontinued. A bookshelf type speaker that uses a uniquely developed hard dome unit. It is a speaker characterized by a well-balanced, clear, and bright sound. There are small scratches, dents, and net holes (Daiki Goto)
Maintenance information: 2024.3.12 operation confirmed (with ATT gaps)
Accessories: none
Main specifications: 3 way 3 speaker bass reflex system frequency band 30Hz to 30kHz impedance 6Ω sound pressure level 94 dB dimensions W390 x H710 x D350 mm weight 27.5 kg/book
Maintained. This is the X-2000R, the best model in the X series. It boasts performance that surpasses the X-1000R, such as a CA (cobalt amorphous) head and a newly designed equalizer amplifier, and you can listen to damped sounds with little noise due to the DBX installation. There are stains and bumps on the exterior. Serial 20066 (Tamura Eiji)
Maintenance information: 2024.4.18 Maintained (flywheel detachable cleaning and capstan shaft cleaning oil applied, capstan belt replacement, grease applied to the foot wheel stator bearing part. Pinch roller drive mechanical disassembly cleaning and grease application, pinch roller cleaning and pinch roller shaft oil application, tape pass check. Head cleaning and head azimuth angle check adjustment. Left and right impedance roller detachment fall cleaning and oil application, left and right tension arm detachment cleaning and cushion replacement, tension sensor cleaning, and tension roller shaft cleaning oil application. Reel stand tension adjustment (FWD/REV-PLAY winding tension and tension adjustment during FF/ REW) playback and recording AMP electrolytic capacitor check and partial replacement, meter lamp, DBX display lamp replacement, replacement procedure due to deterioration of power supply protection resistance. MIC, LINE, OUTPUT volume contact cleaning Contact cleaning by detaching and disassembling the monitor SW, REC mode SW, tape bias selector SW, and DBX SW. Playback level check and adjustment, recording level and vise check and adjustment, DBX amplifier level check and adjustment, recording and playback tests are excellent. Left and right legs missing additional reference value W&F during self-recording and playback (0.02% (WTD))
Accessories: clamper
Main specifications: 4-track, 2-channel stereo format, W432 x H456 x D268 mm, 21.0 kg
※Since it is inexpensive, it will be handed over as is. Tamban 10cm full range unit. An ultra-thin PP diaphragm with reinforced ribs is used. The sound is clear and crisp. A 6-8 liter bass reflex box is recommended (Tamura Eiji)
Maintenance information: 2023.10.1 sweep check OK
Accessories: none
Main Specifications: Rubber Edge Impedance 4 Ohms Sound Pressure Level 87 dB Frequency Band 63 to 17,000 Hz Maximum Input 40 W Baffle Aperture Diameter 94 mm Weight 380 g
The price has been reduced. 2023/6/1 sales price 25,000 yen A fully discrete genuine analog amplifier designed with an amplifier using a total of 10 pairs of carefully selected transistors without using an operational amplifier. It's lightweight, compact, and useful for portable applications. The exterior has scratches and scratches on the main body (Mizusaki Ryo)
Maintenance Information: 2023.6.1 Sound output confirmed
Accessories: AC adapter, USB cable, silicone band, carrying case, original box
Main specifications: input 3.5mm mini terminal output 3.5mm mini terminal input impedance 30kΩ output 200mW (32Ω) 100mW (50Ω) 50mW (300Ω) 15mW (600Ω) W97 x D46 x H19 mm (including volume knob) weight approx. 117 g
Variable Resistor Attenuator Bridge T Type 21 Steps Maximum Attenuation 50 dB Impedance 600 Ohms W45 x 64 mm 140 g with Volume Knob (Kojima Yosuke)
Accessories: volume knob (attached to the main unit)
The disposal price has been reduced! (Member prices are not applicable) 2023/4/15 sales price 148,000 yen Overhauled by the manufacturer! The maniacal 300B power amplifier is now in stock in kit type. This is a product that Sun Valley/Kit stores were fully satisfied at the time and took on a new challenge. You can enjoy the sound unique to Sun Valley, which is plump and has a good tone. The exterior is dull, but there are no noticeable scratches. (FUJISAWA KOSHI)
Maintenance information: 2024.4.15 Maintained by the manufacturer (after fixing production issues, measurement and aging (5H) were completely reworked, and the 300B1 was replaced due to poor output (insufficient output). Since this product is a circuit with a transformer arranged at the input part, the input impedance is designed to be lower than a normal vacuum tube amplifier. Therefore, we recommend using the input volume at the maximum position unless there are special circumstances)
Accessories: power cord, manufacturer measurement table
Main specifications: 300B single power amplifier vacuum tube configuration: first stage 6C6 x 2, output stage 300B with adjustable ham balance only wiring method: all manual wiring bonnet: none Rated output: 8W+8W/8Ω, THD 10% frequency characteristics: 25Hz to 40kHz (1W, -3dB) gain: 25dB power consumption: rated 90W output impedance: 4,8,16Ω (select any system during production) ) Size (including vacuum tube and protrusions) W330 x D280 x H210 mm, weight approx. 12.5 kg
SAEC long-selling model with a 0.6 m digital cable. 6N ultra-high purity copper with excellent transmission characteristics is used as the conductor material, and transmission loss is reduced with accurate impedance matching (Tamura Eiji)
Maintenance information: 2024.4.4 continuity confirmed
Accessories: none
The price has been drastically reduced. 2023/12/11 sales price 15,000 yen*There is no problem with operation, but since it is cheap, it is being delivered as is. Center speaker for the company's STAGE series. Please help build a theater system (Daiki Goto)
Maintenance information: 2023.12.11 operation confirmed
Accessories: instruction manual
Main specifications: 2-way dual 133mm woofer, 25mm aluminum treble unit impedance 6Ω efficiency 88dB W469 x H190 x D220 mm weight 7.95 kg
The price has been drastically reduced. 2024/4/18 sales price 118,000 yen This MC boost transformer is ideal for SPUs using the JS transformer TYPE0.32M No. 6600. The sharp high frequencies and the tenacious sound in the mid and low frequencies make the SPU sound even more energetic. There is rust on the exterior due to paint peeling (Murakoshi Yoichi)
Maintenance information: 2024.4.18 sound output confirmed
Accessories: none
Main specifications: boost ratio 31 times with bypass function, primary impedance 1.5 ohm/secondary impedance 1.5 kΩ dimensions W90 x H68 x D88 mm weight 420 g
*Needle cover missing. G-shell elliptical needle model. The glossy, rich, and heavy sound is attractive without fading. It is an eternal cartridge that fully conveys the appeal of analog. There are slight corrosion irregularities on the shell (Murakoshi Yoichi)
Maintenance information: 2024.4.17 sound output confirmed
Accessories: none
Main specifications: G shell oval needle MC type output 0.2 mV needle pressure 3 to 4.5 g internal impedance 2 ohms dead weight 31 g
G-shell oval needle model from the Herman era. The glossy, rich, and heavy sound is an appeal that never fades. It is an eternal cartridge that fully conveys the appeal of analog (Yasuhito Koshihama)
Maintenance information: 2024.4.25 storefront operation confirmed
Accessories: original box
Main specifications: G shell oval needle MC type output 0.2 mV needle pressure 3 to 4.5 g internal impedance 2 ohms dead weight 31 g
*The headshell is an SPU-G (M) one, but the body is inexpensive because it is GE. Needle cover missing. G-shell oval needle model. The glossy, rich, and heavy sound is attractive without fading. It is an eternal staple cartridge that fully conveys the original appeal of analog. The exterior has rust on the metal parts, and dullness and dirt throughout the body. The needle tip is in good condition (Murakoshi Yoichi)
Maintenance information: 2024.4.17 sound output confirmed
Accessories: none
Main specifications: G shell oval needle MC type output 0.2 mV needle pressure 3 to 4.5 g internal impedance 2 ohms dead weight 31 g
The sound of the shell, which determines the rich sound of the SPU called the “core of the MC cartridge,” is enhanced by blending wood powder and resin. It is a modern SPU that combines the softness and intensity of the classic series sound. It's very slightly leaning to the left. Serial 730862 (Takasaki Atsushi)
Maintenance information: 2024.4.20 sound output confirmed
Accessories: original box, needle cover
Main specifications: MC type output voltage 0.2 mV impedance 2 ohms frequency characteristics 20 to 25,000 Hz internal resistance 6 ohms diamond needle nude elliptical (elliptical needle) suitable needle pressure 4 g dead weight 32 g
SPU-GE reprint model. This is a popular oval needle type. It is a cartridge where you can feel the depth of analog. The rich texture and thick outline set it apart from other cartridges. It's very slightly to the right. Serial 718026 (Takasaki Atsushi)
Maintenance information: 2024.4.20 sound output confirmed
Accessories: original box, needle cover
Main specifications: G shell oval needle MC type output 0.2 mV suitable needle pressure 4 g internal impedance 2 ohms dead weight 30 g
Comes with original box! An A-shell oval needle characterized by the SPU's original direct sound. The sharp, firm, and powerful mid-low range and detailed expressiveness are attractive. There are fewer incidental sounds than the G-shell elliptical type, so you can enjoy an even more direct tone. Serial 924201 (Fujisawa Yukishi)
Maintenance information: 2024.4.6 operation confirmed
Accessories: original box, needle cover
Main specifications: MC type 0.2 mV 3 to 4.5 g internal impedance 2 ohms load resistance 47 kΩ oval needle dead weight 23.6 g (mounter and screws included)
A round needle model that has become valuable. The high range is soft and the bass is thick, and it is characterized by the thickness of the midrange represented by the bobbon-shaped frequency characteristics. The suppleness of the tone creates a sound field that you won't get tired of listening to. Kanchireya is slightly to the left. Serial 21536 (Fujisawa Yukishi)
Maintenance information: 2024.4.6 operation confirmed
Accessories: needle cover
Main specifications: MC type output voltage 0.2 mV needle pressure 3 to 5 g internal impedance 2 ohms weight 31 g
It is the SPU “number one” newly created with the goal of reproducing the thickness and thickness of the sound of old SPUs of yesteryear. Among them, the #1S is a cartridge that uses a round needle, and a wide range is also added. Serial 242699 (Kanai Hidetsugu)
Maintenance information: 2024.4.23 sound output confirmed
Accessories: original box, instruction manual, needle cover
Main specifications: round needle output voltage 0.18 mV internal impedance 2 ohms needle pressure range 3.0 to 5.0 g dead weight 30 g
It is the SPU “number one” newly created with the goal of reproducing the thickness and thickness of the sound of old SPUs of yesteryear. Among them, the #1S is a cartridge that uses a round needle, and a wide range is also added. Serial 312009 (Kanai Hidetsugu)
Maintenance information: 2024.4.23 sound output confirmed
Accessories: original box, instruction manual, needle cover
Main specifications: round needle output voltage 0.18 mV internal impedance 2 ohms needle pressure range 3.0 to 5.0 g dead weight 30 g
※This item is currently sold. Onkyo enabled speaker. It is a design that makes it possible to construct a Dolby Atmos sound field using sound reflection from the ceiling. Accessories such as brackets and cables are missing (Sasaki Shota)
Maintenance Information: 2023.12.11 Sweep Test Good
Accessories: none
Main specifications: sealed impedance 6 ohms, playback frequency band 90 Hz to 20 kHz, W120 x H155 x D153 mm, 1.2 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/4/12 sales price 188,000 yen The successor to the company's hit model Silver8 debuted at Hi-Fi. The color is HGBK (high gloss black) with a sense of luxury. The low range, which is easy to handle yet has a sense of volume, and the clear mid-high range with a wide range are attractive. There are scratches and scratches on the exterior. Serial 700247, 700247 (Fujisawa Yukishi)
Maintenance Information: 2024.4.12 Operation confirmed
Accessories: instruction manual, spikes
Main specifications: 3-way bass reflex type crossover frequency 570 Hz, 3.5 kHz impedance 8 ohms allowable input 200 W efficiency 90 dB size W185 ✕ H1,000 ✕ D300 mm W252 x H1034 x D367 mm (base foot included) weight 20.0 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/3/25 sales price 118,000 yen LINN network player with built-in amplifier. It is equipped with an Ethernet terminal that completes the system simply by connecting a speaker, and supports WAV, FLAC, AIFF, Apple Lossless, AAC, and MP3 playback via LAN. In addition, it is equipped with 1 optical digital and 1 coaxial digital audio input and 1 RCA analog audio input. It can also be connected to devices other than the built-in player and used as a digital premain amplifier. *The volume will be adjusted on the computer. The exterior has a feeling of use such as dullness and small scratches. Serial 1298721 (Hiroki Aso)
Maintenance information: 2024.3.25 Operation confirmed
Accessories: power cable
Main specifications: Compatible audio files: FLAC, ALAC, WAV, AIFF, AAC, MP3 compatible sampling frequency: 7.35k to 192k Compatible bits: 16 bit, 24 bit Input terminals: Ehernet Analog audio: RCA x 1 (impedance; 10 kΩ) Digital audio: RCA (SPDIF) x 1, TOSLINK (Optical) x 1 SP output: L/R x 1 (compatible with banana, bare wire, Y lug terminals) LINE Output: RCA x 1 SN Ratio: 105 dB Frequency Characteristics: 0 Hz - 30 kHz Output: 70W (4Ω) W191 x H80 x D274 mm Weight 2.65 kg
Real sound processor for home theaters Just by connecting to a home theater speaker, the sound image and localization become clear, the live feeling increases, and the surround effect is enhanced. There are tape marks on the exterior. Serial 001288 (Tamura Eiji)
Maintenance information: 2024.4.24 Operation confirmed
Accessories: none
Main specifications: Compatible impedance of 4 ohms to 6 ohms is desirable, maximum output of 1 kW or less is desirable, W113 x H41 x D56 mm, mass approx. 170 g
When connected to a speaker, it reduces speaker impedance fluctuations in the mid to high range. More faithful speaker driving is possible, speaker resolution and stand-up are improved, and natural afterglow is also reproduced. There are scratches on the exterior. Serial 00753, 00754 (Fujisawa Yukishi)
Accessories: instruction manual, original box
Main specifications: W100 x H47 x D117 mm approx. 190 g/piece
The price has been drastically reduced! 2024/4/3 sales price 79,800 yen CASTLE's small studio monitor is in stock for the first time at Hi-Fi. A special version of the model that has received high praise since its inception. Even though it is crowned with a monitor, you can feel the high level of texture unique to being made in England that is easy to listen to. You won't get tired of listening to the supple sounds of vocals and strings. The exterior is a saran net, and there are small scratches on the main body. Serial BJH0009 (Yonejima Satoshi)
Maintenance information: 2024.4.3 sweep test is good
Accessories: saran net
Main specifications: 2-way rear bass reflex type frequency characteristics 60Hz-20kHz output sound pressure level 88dB rated impedance 8Ω W165 x H280 x D235 mm 5.1 kg
The disposal price has been reduced. 2024/4/4 sales price 898,000 yen British original enclosure, equipped with 15 inch monitor gold! Refreshing York has regained its original tone through our refreshment maintenance. It is a speaker representing TANNOY that brings out the appeal of all kinds of sources. In particular, the beautiful, glossy sound in string and vocal music plays a sound that once you hear it, you won't be able to leave your ears (Sasaki Shota)
Maintenance information: 2024.4.4 Maintained (exterior repair/polishing/clear finish. Maintenance: net cleaning/fraying repair/repasting, sound-absorbing material removal. Unit maintenance: Magnetic circuit gap cleaning center adjustment for both low and high frequencies. Network maintenance: frequency characteristic check, ATT cleaning, terminal cleaning)
Accessories: none
Main specifications: bass reflex system floor type 15 inch coaxial 2 way (Monitor Gold 15 inch) frequency characteristics 30 Hz to 20,000 Hz crossover frequency 1,000 Hz maximum input 50 W impedance 8 ohms size W597 x H1,070 x D375 mm
The disposal price has been reduced! (Member prices are not applicable) 2024/4/2 sales price 79,800 yen Hi-Fi Hall first arrival! A compact and elegant DALI tall boy speaker with sharp low frequencies and clear midrange, and an airy treble range. The exterior has a scratch on the stand, a scratch on the side of the main unit, and a small scratch on the top plate. Serial 6255811 (Sato Wataru)
Maintenance information: 2024.4.2 sweep test is good
Accessories: instruction manual, spike, saran net
Main Specifications: Frequency Characteristics: 39~26kHz 88dB Impedance 4Ω Tweeter 29mm Soft Dome Midrange/Woofer 130mm/SMC Wood Fiber Cone Driver ✕ 2 Dimensions W162 ✕ D283 ✕ H830mm Weight 10.8 kg
Internal and external maintenance has been applied and brushed up. The vivid sense of dynamism and the sharpness of the high frequencies typical of YAMAHA have been revived. It has a low frequency thickness that 1000 monitors don't have. It is a timeless masterpiece with a clear sense of transparency, upper and lower driving force, and the smooth connection, and the heavy exterior with an ebony finish that stands out at a glance even today. It is in good condition due to maintenance. Serial 11478L 11478R (Yamato Yuki)
Maintenance information: 2024.4.1 operation confirmed
2023.9.4 Maintained (exterior repair/polishing/clear finish. Rear baffle repair/painting. Saran net replacement. Unit frame painting. Network maintenance (Since the terminals have already been replaced with external products, adjust the direction and tighten, apply a screw fastener, and replace the mounting screws. ATT contact status check (check that there are no gaps). A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Input/output waveform and balance check, sound output check) Unit detachable)
Accessories: saran net
Main specifications: 3-way sealed playback frequency band 40Hz to 20kH sound pressure level 90dB rated input 50W maximum allowable input 100W impedance 8Ω crossover frequency 500Hz/6kHz dimensions W395 x H710 x D349 mm 39 kg
Line transformer using TANGO's input transformer, NN-600-600. The overall sound resolution is increased, and the sense of sound pressure is also enhanced. Recommended for those using speakers with horn drivers. TANGO badges are discolored, and there are tape marks and bumps on the chassis (Kojima Yosuke)
Maintenance information: 2024.4.18 Operation confirmed
Accessories: none
Main specifications: primary impedance 600 Ω (150 Ω split) secondary impedance 600 KΩ (150 kΩ split) primary inductance 70 H W140 × H110 × D100 mm 1.8 kg (actual measurement, not including protrusions)
Input transformer pair sale primary impedance 600 Ω (150 Ω split) secondary impedance 600 KΩ (150 kΩ split) primary inductance 70H W50 × H70 × D57 mm 0.75 kg/piece (actual measurement, not including protrusions) The badge is discolored, and there are scratches in places (Kojima Yosuke)
Accessories: specifications
The price has been reduced! 2020/11/9 sales price 70,000 yen maintenance completed. This is a 2-way network. Since bass can be pushed out well, and high frequency adjustment ranges can be obtained with 2 types of HF/MF attenuators, it is a model that is easy to match the desired sound quality. There are small scratches on the exterior due to the feeling of use. Serial 05234 07210 (Makoto Kono)
Maintenance information: 2020.11.9 maintained (common wiring reinforcement terminal solder removal, rust removal treatment, cleaning, ATT (x4) contact disassembly cleaning, contact grease application, frequency characteristic measurement check (~ approx. 42 kHz), continue using the original capacitor for good results, input/output waveform and balance confirmation sound check)
Accessories: none
Main specifications: W114 x H190 x D228 mm 1.8 kg Crossover frequency 1.2 kHz Impedance 8 ohms Level control is continuously variable up to -8 dB in the middle range is 2 kHz and the high range is continuously variable up to -6 dB at 10 kHz
The disposal price has been reduced. Member prices are not applicable. 2023/10/23 sales price 29,800 yen ※Currently sold. Comes with a special case! Portable headphone amplifier with built-in D/A converter. DSD256 (11.2 MHz/1 bit) PCM supports native playback of up to 768 kHz/32 bit. Please enjoy the sound quality unique to a thick mojo in the mid to low range. There is dullness and a feeling of use (Sasaki Shota)
Maintenance information: 2023.10.23 Operation confirmed
Accessories: original box
Main specifications: output level 35 mw/600 ohm, 720mw/8 ohm, output impedance 0.075 Ω, dynamic range, 125 dB input system, 3 optical systems, 1 coaxial x 1, microUSB x 1, 2 output systems, headphone jack x 2, charging time, approx. 5 hours continuous operation time, approx. 8 hours W82 x H60 x D22 mm 180 g
※Since the cantilever is slightly raised, it is inexpensive. Mid-range models in the MC Star series, which come in 3 types. Both models have different sounds, and they are all unique, but 20W is a model that places particular emphasis on the mid-range. The sound is warm in tone, and has an extrusive, and comfortable sound that goes through the SPU. The wooden body made of Yamanaka lacquer, which is a traditional Japanese craft, is also beautiful.
Maintenance Information: 2024.4.25 Operation confirmed
Accessories: none
Main specifications: MC type output voltage 0.5 mV suitable needle pressure 2.3 g recommended load impedance 10 to 200 ohms dead weight 10.5 g
This standard cartridge is particularly famous in the company's MC series. It has good stretch in the high range and a texture that feels good against the skin, has thickness and density in the mid-range, and it is a tone that makes you feel a sense of temperature (Oikawa Tetsuji)
Maintenance Information: 2024.4.25 Operation confirmed
Accessories: none
Main specifications: MC type output voltage 0.09 mV needle pressure 1.7 g playback frequency band 20 to 20,000 Hz load resistance 10 ohms internal impedance 3 ohms dead weight 7 g
※1 bottle only. Maintained! This is a rare blue frame (above) model LX5. The impedance is 8 ohms, and the cross is 500 Hz, so be sure to use a 175 or 375 driver that uses 8 ohms! There are spots, rust spots, and small scratches. (Honda Maki)
Maintenance information: 2021.12.21 Conductivity confirmed 2019.4.4 Maintained (re-fix the internal coil with silicone agent. Remove rust from terminals and mounting screws, clean, and tighten. ATT (SW type) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. (Input/output waveform and balance check, sound output check)
Accessories: No accessories
Key Specifications: Crossover Frequency: 500 Hz Level Control: 3 Position Switch Input Impedance: 16 ohms 159 x 153 x 120 mm 2.3 kg
※Since it is cheap, it will be handed over as is. Marantz 10cm full range speaker. There is no habit, and it makes a well-balanced sound from high to low frequencies. It doesn't take up much space, so you can set it up anywhere. The exterior has scratches, dirt, scratches, etc. Also, there is color peeling and partial deformation on saran. Serial MZ01748010115 (Fujisawa Yukishi)
Maintenance information: 2024.2.25 Operation confirmed
Accessories: saran net
Main specifications: 1 way, 1 speaker, bass reflex system, setting free type, rated input 35W, impedance 6Ω, playback frequency 50 Hz to 20 kHz, W230 x H150 x D150 mm
The disposal price has been reduced! Member prices are not applicable. 2024/2/28 sales price 248,000 yen Refreshed and maintained with internal and external maintenance! The clear and dynamic sound quality, and the deep, powerful sound of 123A is more powerful than its size, and makes you enjoy jazz and rock exhilarating. This speaker is perfect for playing jazz on records (Yonejima Satoshi)
Maintenance information: 2024.2.28 Maintained (enclosure polishing/oil/wax coating, baffle painting. Maintenance: frame polishing/oil finish, net replacement. Woofer cone paper paint Tweeter maintenance: New urethane ring created, frame cone paper coating. Network maintenance: frequency characteristic check, ATT disassembly cleaning, terminal cleaning/screw replacement)
Accessories: saran net
Main specifications: 2 way 2 speaker bass reflex bookshelf type unit configuration high range LE25 (3.6 cm) + low range 123A (30 cm cone) impedance 8 ohms crossover frequency 2 kHz dimensions W360 x H600 x D 300 mm weight 20 kg
The disposal price has been reduced. Member discounts are not applicable. 2023/6/24 sales price 178,000 yen Maintenance has been carried out and deteriorated capacitors etc. have been replaced! A newly created power supply is included. Genuine RF MC cartridge head amplifier The RCA terminal specification makes it easy to use, and has a separate power supply structure. The delicate, clear, and powerful sound is attractive (Daiki Goto)
Maintenance information: 2023.6.24 maintained (new power supply manufactured because the power module is defective but cannot be repaired, all deteriorated capacitors replaced, pin jack deterioration replaced, gain changeover switch replaced due to poor contact, each gain readjusted, operation inspected, (there are no current problems with the module)
Accessories: copy of instruction manual
Main specifications: Gain can be adjusted in 3 levels; input impedance can be used up to 45 ohms W175 x H60 x D210 mm 1.4 kg
Maintained! The 306 series was supported as a pure audio entry model. It has plenty of phono circuits, is MM/MC compatible, and impedance can be adjusted. Clear, high quality sound quality with W super servo system. I feel that the sound quality, which has a slight core, is good in this era. You can see a feeling of use such as appearance, dullness, small scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.22 maintenance completed (mode, recout, input, subsonic, cartridge, phono selector switch disassembly, polishing grease application, replacement of all indicator lamps, solder repair, pin jack polishing, internal inspection and cleaning, each volume, switch cleaning, operation confirmation)
Accessories: instruction manual
Main specifications: PHONO (MM/MC) 2 system frequency characteristics 0.8 Hz to 170 kHz dimensions W480 x H100 x D403 mm weight 10.5 kg
The price has been reduced! 2024/4/21 sales price 39,800 yen This is a compact Dali speaker with an attractive sound that is warm and feels good against the skin. They play vocals, chamber music, etc. comfortably. The exterior is dull. Serial 5431394, 5431394 (Fujisawa Yukishi)
Maintenance information: 2024.4.21 operation confirmed
Accessories: original box, saran net
Main specifications: Playback frequency characteristics approx. 45 Hz to 30 kHz crossover 2.5 kHz/14 kHz input sensitivity approx. 86 dB impedance 6 ohms recommended amplifier output 25 to 100 W W150 x H325 x D260 mm 4.8 kg
The price has been drastically reduced! 2024/4/18 sales price 178,000 yen 2024/1 maintenance completed! It is a Harves speaker with increased appeal, such as the richness of the sound typical of an HL MONITOR. The Harves-like sound, which is characterized by a relaxed sound in addition to the mid-range density unique to those made in England, is attractive. Exterior maintenance has been carried out on the exterior, but in addition to scattering repair marks, there is a feeling of use over time, such as undulations on the woofer edge. *Saran net is not included. Serial 3349A 3349B (Tomonori Asaine)
Maintenance information: 2024.1.12 Maintained (exterior repair stain tinted front baffle repair polishing paint rear baffle cleaning
Woofer edge repair, protective agent application (with undulations), terminal replacement unit, detachable tweeter, corrosion, disconnection repair, diaphragm, dome coat treatment, 1 voice coil, bobbin deformation correction)
Accessories: none
Main specifications: 2 way 2 speakers, 22.5 cm cone woofer/2.5 cm soft dome tweeter impedance 8 Ω crossover 2,000 Hz sound pressure level 87 dB, W325 x H640 x D330 mm, 13.5 kg
The price has been drastically reduced. 2024/4/22 sales price 228,000 yen The HL series has an attractive smooth, beautiful sound unique to British BBC monitors. As expected, there is plenty of noise regardless of genre, from jazz and classical music to rock and pop music. From the design, which has just the right amount of sound of the box and the presence of guests, you can hear an unrivaled beautiful sound. It is in good condition without any major noticeable scratches (Oikawa Tetsuji)
Maintenance information: 2024.4.22 operation confirmed
Accessories: none
Main specifications: 2-way 2-speaker bass reflex system unit, 20 cm cone type for low range, 2.5 cm dome type playback frequency band 43 Hz to 20 kHz output sound pressure level 86 dB impedance 8 Ω maximum input 150 W W271 x H520 x D315 mm 12.5 kg
The price has been drastically reduced! 2024/4/17 sales price 69,800 yen ※It is cheap because it has a tobacco smell. Hi-Fi Man's planar drive headphones have a high resolution, and the low frequencies are clear and easy to listen to. The sound balance is flat and the high cushioning is also impressive. The exterior smells like tobacco and there are creases on the cable (Tamura Eiji)
Maintenance information: 2024.4.16 Operation confirmed
Accessories: original box, connection cable
Main specifications: planar drive impedance 50 ohms sound pressure sensitivity 83.5 dB playback frequency band 8 Hz to 65 kHz 505 g
A headphone amplifier compatible with headphones with various impedances, from foreign-made headphones with high impedance to headphones made in Japan with low impedance. The high-frequency sound is very beautiful, and the sound is transparent, and you can feel a sense of realism. Equipped with a speaker terminal, it can be used as a simple pre-main amplifier. The exterior is dull. Serial HD53R062.5045005 (Tamura Eiji)
Maintenance information: 2024.4.24 Operation confirmed
Accessories: power cable, instruction manual
Main specifications: 1 input RCA, 1 XLR system, 1 output speaker system, 2 headphone systems W217 x H51 x D391 mm 2.6 kg
The price has been drastically reduced! 2024/4/22 sales price 798,000 yen Maintained! A model equipped with a variable switching phono, imported from regular RF. This is a high-end preamp that made the CELLO name known. It is no exaggeration to say that the elegant and beautiful tone, which is precise and delicate, has outstanding expressiveness and unique luster, is a work of art. In addition to the appearance being dull, there are small scratches on the top plate. Serial 0683 (Hiroki Aso)
Maintenance information: 2024.4.22 maintained (all corrected for disconnection of the Y lug part of the DC cable, replacement of all power supply parts and body deterioration capacitors, replacement for volume galli, replacement, replacement, RCA jack for rust, polishing specs inspection for each operation, the phono is set for MM with a gain of 36 dB input impedance of 50K)
Accessories: instruction manual, power supply unit, power cable
Main specifications: input imbalance (RCA) 8 systems/PHONO (MM/MC) 1 system/balance (Fisher) 1 system output unbalance (RCA) 2 system/balance (Fisher) 1 system body/W515 x H140 x D370 mm weight 10.1 kg power supply/W240 x H100 x D335 mm weight 5.1 kg
This is an MC-type cartridge from Entre. The sound is slightly stiff and sharp, and the sound quality is sharp. The outline and texture of the low frequencies are also firm. There are no particular bends. Serial 39354 (Tamura Eiji)
Maintenance information: 2024.4.17 operation confirmed
Accessories: none
Main specifications: MC type output 0.5 mV needle pressure 1.7 g to 2.3 g (appropriate 2.0 g) impedance 6.3 ohms dead weight 5.9 g
The price has been reduced! 2024/4/11 sales price 45,000 yen Woofer edge softening treatment was completed in March 2021! The sharp mid-high range, which is typical of a diamond tone, is characteristic. The low frequency thickness unique to 30 cm is also attractive, so you can enjoy it in all genres. There are some dents on the exterior. Serial 16747/16900 (Yonejima Satoshi)
Maintenance information: 2021.3.6 Maintained (softened)
Accessories: saran net
Main specifications: 3 way 3 speaker sealed impedance 6 Ω playback frequency band 35 Hz-35 kHz crossover 500 Hz/4 kHz maximum input 230 W sound pressure 91 dB W380 x H680 x D325 mm 27 kg
The price has been reduced. 2024/4/16 Sales price 198,000 yen Edge softening treatment, etc. Maintenance completed! Comes with a 7.5 kg DK-2000Z stand dedicated to the DK-2000Z class weight! The DS-2000Z thoroughly sought realistic sound. The sound quality is beautiful and glittering, conveying even the feeling of air with sound. Please try the high resolution sound source. There is a feeling of use due to appearance, dullness, light scuffs, etc. (Kobayashi Hitoshi)
Maintenance information: 204.4.16 maintenance completed (exterior veneer float repair/cleaning, saran net replacement, woofer edge softening treatment)
Accessories: instruction manual, saran net
Main specifications: 3-way sealed system, bookshelf type speaker impedance 6 ohms playback frequency band 27 Hz to 80000 Hz output sound pressure level 90 dB maximum input 180 W dimensions W380 x H725 x D315 mm (356 mm with net) weight 37 kg stand dimensions W380 x H170 x D315 mm weight 27.5 kg
MC cartridge using LC-OFC (linear crystal/oxygen-free copper) wire based on DL-103. Familiar sound with a wide range. The supple sound makes it comfortable to listen to. The exterior has a feeling of use, such as dullness on the body. Serial 4126 (Hiroki Aso)
Maintenance information: 2024.4.21 sound output confirmed
Accessories: none
Main specifications: MC type output 0.25 mV, proper needle pressure 2.2 to 2.8 g, internal impedance 13 ohms, own weight 8.5 g
※There is no problem with operation, but it is currently sold because it is cheap. A small 2-way speaker made by ONKYO. The bass reflex system allows you to enjoy low frequency playback with a compact appearance yet a sense of volume. There is slight stickiness on the front (Daiki Goto)
Maintenance information: 2024.4.10 operation confirmed
Accessories: none
Main specifications: 2-way bass reflex type rated impedance 4 ohms maximum input 120 W rated sensitivity level 82 dB W156 x H249 x D221 mm 4.1 kg
The disposal price has been reduced. Member discounts are not applicable. 2023/12/13 Sales price 138,000 yen Maintenance completed! Newcomb tube mono prime. An output of about 12W is output using a 6V6 output tube. It has an adjustment function for a total of 36 fine phono curves, 6 low frequencies and 6 high frequencies. The stylish look reminiscent of Old Marantz, such as the hood on the back, is irresistible. Since the input terminals are on the bottom, it is necessary to devise how to insert the RCA cable. The standard LEVEL position is M. Adjust the volume with LOUDNESS. SELECTOR's RUMBLE FILTER is valid only for PHONO. ※The hood is fitted very tightly, so it cannot be removed normally. There is a feeling of use due to appearance, dullness, small scratches, abrasions, etc. (Murakoshi Yoichi)
Maintenance information: 2023.12.12 maintenance completed (earth terminal added to bottom, vacuum tube 6AV6 replacement, 100 μF electrolytic capacitor and lug terminal added to 80/10 μF block capacitor, base leg replacement/HUM ADJ readjusted, vacuum tube socket and RCA jack caulk repair. Operation checked (measured at 11 to 15 W SP: 8 Ω with rated output AC 100 to 117 V).
Accessories: none
Key Specifications: 6V6P.P. Rated output 12 W LINE 3 system, PHONO (MM) 1 speaker compatible impedance 8, 16 ohms, W322 x H112 x D240 mm, 6.8 kg