Maintained by the manufacturer! This mono power amplifier was developed as the first full-scale high-output power amplifier for consumer use. The sound quality is unique to Accuphase, which has high power and is full of subtlety. Equipped with a digital meter that instantaneously calculates real power. By switching between modes, it is easy to drive even ultra-low impedance speakers. There is a feeling of wear on the exterior such as scratches. E1X029 E1X030 (Jun Tamai)
Maintenance information: 2024.6.6 Accuphase maintained (relay contacts replaced due to deterioration, all switches, volume, reworked due to contact cleaning, parts replaced due to stress deterioration, safety confirmation, pressure resistance test, operation characteristics check, each readjusted cleaning pair, similar treatment for matching characteristics)
Accessories: original box
Main specifications: 800W+800W (8Ω) W481 x H239 x D489 mm 47.2 kg
Hi-Fi is in stock for the first time! GLANTZ statically balanced tone arm. The main body is machined from hard stainless steel, and the structure is firmly supported by 4 large bearings, and it has high traceability performance with reduced resonance and blurring, and exudes a sharp sound. Since there is weight in the weight part, you can use heavy cartridges such as OrtoFon's SPU without lowering the weight too much. The exterior is generally good (Takahashi Nobuyuki)
Maintenance information: 2024.6.2 operation confirmed
Accessories: instruction manual, headshell, phono cable, cartridge installation screw wrench
Main specifications: Form Static balance system Total length 330 mm Effective length (arm fulcrum to needle tip) 305 mm Effective length (arm fulcrum to center of turntable) 290 mm Compatible cartridge 16 to 43 g weight 1.14 kg Overhang 15 mm Mounting base internal dimensions 16 mm Mounting hole 30 mm
Full maintenance from each unit to network and exterior! This is a 4343BWX with blue baffles and walnut specifications. The instantaneous power, sharp treble, volume and dynamism of the bass are outstanding. It's one step ahead of current speakers in terms of localization, but it's rare to find a speaker that makes on-mic recordings of all ages sound better than this. It has a beautiful finish due to exterior maintenance (Oikawa Tetsuji)
Maintenance information: 2024.5.27 Maintained (exterior repair/polishing/oil finish baffle repair/paint saran net repair/frame repair: edge replacement, cone paper coating, in-gap cleaning/center adjustment midmaintenance: edge replacement/cone paper coating driver maintenance: magnetic circuit rust removal/gap cleaning/center adjustment, sound absorbing material replacement, terminal cleaning/screw replacement Tweeter maintenance: magnetic circuit rust removal/gap cleaning, terminal cleaning/screw replacement network maintenance: frequency characteristic check, ATT/switching SW cleaning, partial defective resistance/capacitor replacement unit detachment/diffuser repair)
Accessories: none
Main specifications: 4-way monitor speaker bass reflex playback frequency band 35 Hz to 20 kHz (+- 3 dB) crossover frequency 300 Hz/1250 Hz/9500 Hz impedance 8 Ω output sound pressure level 93 dB dimensions W635 x H1,051 x D435 mm weight 83.9 kg
A high-performance integrated SACD/CD player that is the successor to the DP-550. It is a stable sound that makes you feel the thickness of the mid to low frequencies, and the spread of sound from low to high frequencies is not excessive or insufficient. The USB terminal is compatible with 384 kHz 32 bit and 11.2896 MHz 1 bit DSD. The tray button printing is missing. There is a small scratch on the side (Sasaki Shota)
Maintenance information: 2024.6.9 operation confirmed
Accessories: remote control, manual, power cable
Main specifications: 4MDSD+ sampling frequency HS-LINK 32kHz-384kHz (PCM), 2.8224MHz, 5.6448MHz (DSD), coaxial32kHz-192kHz, optical32kHz-96kHz (PCM), USB32kHz-384kHz (PCM), 2.8224MHz, 5.6448MHz (DSD), 11.2896 MHz (DSD/ASIO only) output Level control 0 dB to -80 dB frequency characteristics 0.5-50,000 Hz dynamic range 116 dB dimensions W465 x H151 x D393 mm weight 18.8 kg
This is the L-type TH-9708, which is the highest peak step-up transformer along with cotters. The detailed, glossy, and deep sound is the true essence of analog playback. The degree is generally good. Serial 890167 (Murakoshi Yoichi)
Maintenance information: 2024.6.12 sound output confirmed
Accessories: original box
Main specifications: primary impedance: LOW 3 ohms size W16.5 x H12 x D10 cm dead weight 2.75 kg
2024.4 Maintained! Equipped with Philips CDM4PRO, this player is easy to operate, has plenty of professional features, and excellent durability. It has a higher frequency extension than the A730, and the overall balance from bass to treble is good, and the sound has a solid sense of sound pressure. There is dullness and small scratches all over the exterior (Kobayashi Hitoshi)
Maintenance information: 2024.4.7 Maintained (CD mechanical pickup is movable by checking, dismantling, check assembly → reading OK. All other internal parts of the NG part have been replaced. CD disc plate replacement ~ aging test 6 days ~)
Accessories: power cord, instruction manual (copy)
Main specifications: CDM4PRO mechanical analog output 2 systems (RCA/XLR), 1 digital output system (AES), 1 clock system (BNC) W320 x H131 x D355 mm 6.1 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/5/31 sales price 598,000 yen Manufacturer maintained! A famous machine loaded with excellent phono amplifiers. This is a good quality control amplifier that lets you hear clean, transparent sound. There are only top quality models, and the thickness and luster of the sound will not fade even after nearly 30 years have passed. The exterior has dullness and small scratches, and there are noticeable abrasions on the left side. Serial A2X643 (Takahashi Nobuyuki)
Maintenance information: 2024.5.31 Maintained (capacitor replacement logo, lamp replacement, each switch, input/output terminal contact cleaning, DC offset voltage readjustment of each amplifier, internal and external cleaning functions, performance check, pressure resistance, safety check)
Accessories: none
Main specifications: input terminal/RCA5 system, XLR2 system, tape input/output terminal 2 system, PHONO input 2 system pre-out/RCA2 system, XLR2 system W468 x H171 x D415 mm 25.1 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/6/15 sales price 478,000 yen Maintained by the manufacturer! Current model of the project's belt drive player. Equipped with Ortphone's popular dynamic balance arm RS-309D. The company's commitment is packed with everything from the 9.5 kg aluminum alloy platter and selected ultra-low noise synchronous motors to neodymium magnetic floating feet. The exterior has bumps and burrs that look like bumps on the corners. A protective sheet is attached to the dust cover, but it remains as is (Fujisawa Yukishi)
Maintenance information: 2024.6.15 manufacturer maintained (belt replaced. (Platter bearing grease application, inspection of each part, operation check)
Accessories: instruction manual, stabilizer, power cord, head shell, template, needle pressure gauge, dust cover, EP adapter, gloves
Main specifications: belt drive, compatible with 33, 45, 78 rotations, RS-309D: long arm needle pressure 0 to 5 g, cartridge weight 18 to 40 g (including shell), effective length 326 mm, effective length 311 mm, overhang 15 mm, height adjustment range 42 to 55 mm, W550 x H250 x 450 mm, 22 kg
The disposal price has been reduced (member prices are not applicable). 2024/6/15 sales price 448,000 yen Levinson's long-selling prime amplifier. A dual monaural configuration that is thoroughly packed into a single chassis while keeping the design concept of separation intact. You can be satisfied with all music genres with quality that easily surpasses separate amplifiers. There are threads and dullness (Sasaki Shota)
Maintenance information: 2024.6.15 Maintained (volume and urethane bushing inside selector knobs replaced with new ones. Operation confirmed)
Accessories: remote control, manual, power cable
Main specifications: 100W+100W (8Ω) XLR input x 2 system RCA input x 3 system gain adjustable (preamp section 0/6/12 dB) W445 x H162 x D483 mm 29.5 kg
The price has been drastically reduced. 2024/6/1 sales price 378,000 yen Maintained! The flagship model of the Macintosh power amplifier with a silver panel. It is characterized by its strong, dense sound. The extrusion is strong and goes great with JBL large monitor speakers. The dynamism in the mid to low range, which is difficult to obtain with current Mackin power amplifiers, is attractive. There are scratches and stains on the exterior, and rust can be seen on the top plate and back panel (Mizusaki Ryo)
Maintenance information: 2024.6.1 maintained (transistor in driver board, LDR, capacitor deterioration, GAIN, VOL noise, meter board capacitor deterioration, power supply board capacitor deterioration, meter lamp, display lamp deterioration → replacement. Meter dismantling terminal lead wire soldering treatment, MODE SW dismantling cleaning, operation check, power stage check OK)
Accessories: power cord, copy of instruction manual
Main specifications: 500W+500W (1000W when mono) equipped with power guard circuit W483 x D465 x H263 mm 60.3 kg
The price has been drastically reduced. 2024/6/17 sales price 378,000 yen ※Heavy weights are being ordered. The classic model of the belt drive and long arm system, with the SME3012R mounted on the TD-521RW. A very silky sound that resonates loudly and unrelated to vibrations, which strikes the heart of the sound quality of a record player. You can enjoy it with a variety of cartridges regardless of whether they are heavy or lightweight. *Since it is TD-521, there is no ESOS (semi-auto stop) mechanism. In addition to fading on the exterior and overall appearance, dullness and a feeling of use can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.6.16 Operation confirmed
Accessories: transport lock, instruction manual power cord
Main specifications: [TD521] belt drive type floating suspension mechanism compatible with 33/45/78 rotations [3012R] long arm static balance universal type effective length 307 mm compatible cartridge dead weight 1.5 to 26 g (excluding shell)
The disposal price has been reduced. 2024/5/10 sales price 498,000 yen Both inside and outside have been maintained! Crescendo is a speaker system developed by Electri and sold with Altech's approval. This time it's an original original box specification with the 605B mounted on it. You can enjoy the tasteful design unique to vintage speakers and the crisp American sound with good texture and momentum. The exterior is also beautifully finished due to maintenance, but there are repair marks on the net (Sasaki Shota)
Maintenance information: 2024.5.10 Maintained (exterior cleaning/touch repair. Network assembly) 2023.9.3 maintained (exterior repair/polishing/clear finish front and rear baffle repair/paint saran net simple cleaning
Unit maintenance (low range side: viscoid adjustment/center adjustment, high frequency side: lead disconnection repair, magnetic circuit rust removal/gap cleaning/center adjustment, terminal contact cleaning) network maintenance (characteristic check, terminal cleaning) unit detachment)
Accessories: none
Main specifications: frequency characteristics 20 to 20,000 Hz, use unit 38 cm, 605B (coaxial type with built-in horn), maximum input 50 W, output sound pressure level 97 dB, crossover frequency 1.6 kHz, impedance 16 Ω
W690×H1018×D485mm
Genuine Electri While being clear and precise, this is a powerful machine that also has the thickness and intensity of sound of successive Macintosh control amplifiers. It is a famous machine with a deep sense of nostalgia that is compatible with both vintage and modern models. Using the familiar 5-band equalizer, it is also possible to change the desired tone depending on the song. The exterior has blows, line scratches, and repair marks. Serial JHD3514 (Fujisawa Yukishi)
Maintenance information: 2018.8.30 Maintained (main volume, balance volume, etc. Contact cleaning. Switch contact cleaning. Head amplifier section and EQ volume circuit capacitor replacement. Power cord replacement. (Check the operation of each input/output)
Accessories: No accessories
Main specifications: built-in monitor amplifier with 5-band equalizer (20W x 2/8Ω), compatible with balanced input/output, PHONO (MM) compatible, W468 x H183 x D432 mm, 12 kg
The price has been drastically reduced. 2024/6/12 sales price 328,000 yen An active speaker from the “Formation Suite” series wireless audio compatible with high-resolution transmission. One unit is powered by a 125W digital amplifier. It features a high-quality sound that casually expresses a sense of dynamism when the sound starts up. It is a system that is likely to become a new listening style in the future, as it can also support network playback using Roon without using a separate amplifier. There are thin threads here and there (Oikawa Tetsuji)
Maintenance information: 2024.6.12 Operation confirmed
Accessories: power cable, instruction manual
Main specifications: 2-way active speaker output 125W x 2 Wi-Fi, AirPlay 2, Spotify Connect, Roon Ready compatible Bluetooth version: 4.1 Bluetooth compatible codecs: SBC, AAC, aptX HD W197 x H395 x D305 mm 10.6 kg/unit
The price has been reduced. 2024/6/19 sales price 278,000 yen Maintenance was completed in 2024/5. This is a full set that combines 33 QUAD original transistor preamps and 303 power amplifiers with tuner FM3. Comes with a wood case that allows 33 and FM3 to be built in parallel. The impression is that the natural atmosphere has definitely increased, and the glossy way it rides and the sound that goes through the core make you think it's a vacuum tube amplifier. The wood cabinet has also been beautifully finished due to repairs (Oikawa Tetsuji)
Maintenance information: 2024.5.4 maintained (internal check, power supply, filter C, HPX circuit C, etc., there are many differences in capacity → replacement f cover misalignment → readjust, tuning indicator lamp back change, DIN SP-RCA female cable damaged → created)
Accessories: power cable, connection cable (2 types: DIN-RCA and DIN-DIN types), copy of the instruction manual, FM coaxial connector
Main specifications: [303] W550 x H113 x D220 mm weight approx. 7.0 kg (actual measurement) [33] 3 input/line systems, 1 phono system (MM) [FM3] tubular FM dedicated tuner with automatic stereo/mono switching
Internal and external maintenance has been applied and brushed up. The vivid sense of dynamism and the sharpness of the high frequencies typical of YAMAHA have been revived. It has a low frequency thickness that 1000 monitors don't have. It is a timeless masterpiece with a clear sense of transparency, upper and lower driving force, and the smooth connection, and the heavy exterior with an ebony finish that stands out at a glance even today. It is in good condition due to maintenance. Serial 11478L 11478R (Yamato Yuki)
Maintenance information: 2024.4.1 operation confirmed
2023.9.4 Maintained (exterior repair/polishing/clear finish. Rear baffle repair/painting. Saran net replacement. Unit frame painting. Network maintenance (Since the terminals have already been replaced with external products, adjust the direction and tighten, apply a screw fastener, and replace the mounting screws. ATT contact status check (check that there are no gaps). A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Input/output waveform and balance check, sound output check) Unit detachable)
Accessories: saran net
Main specifications: 3-way sealed playback frequency band 40Hz to 20kH sound pressure level 90dB rated input 50W maximum allowable input 100W impedance 8Ω crossover frequency 500Hz/6kHz dimensions W395 x H710 x D349 mm 39 kg
Cabinet replaced with aurora sound, manufacturer maintained! MM/MC phono equalizer from a handmade amplifier workshop. A model that achieves flat characteristics without coloring using the latest semiconductor technology and a complete DC circuit using the latest semiconductor technology and a Rundahl transformer. Equipped with various functions such as MC/MM switching, MC impedance switching, direct/subsonic filter switching, stereo/mono switching, and cartridge demagnetization, etc., stress-free operability is also attractive. Serial 4J13104 (Fujisawa Yukishi)
Maintenance information: 2024.6.16 manufacturer maintained (LED left and right replacement. Replace it with a new pink color. DC offset readjustment for amplifier section, voltage check for each part. (MUTE SW readjustment, measurement and overhaul of each part.)
Accessories: instruction manual, power cord, connection cord
Main specifications: [main body] W260 x D250 x H100 mm approx. 3 kg [power supply part] W114 x D200 x H70 mm approx. 1.4 kg
The price has been reduced. 2024/6/6 sales price 258,000 yen Maintained! The top Macintosh model in the golden age. You can enjoy the thick and bold Macintosh sound. Comes with an easy to handle 5-band equalizer. An easy-to-use preamp that can be combined with speakers and power amplifiers of a wide range of ages. There is a slight feeling of use such as scratches on the top plate. Serial AY3749 (Kobayashi Hitoshi)
Maintenance information: 2024.6.5 maintenance (TR in the EX Pander board, Tr replacement in the headphone board, operation check, connector caulking cleaning, solder processing) maintained (flat cable replacement, each SW and 2023.3.30 and VOL cleaning, RCA cleaning ※ internal capacitor, lamp, cable replacement (made by another company) IC replacement operation check gap cannot be completely removed) 2022.9.29 Maintained (switch, volume contact cleaning, flat cable replacement, electrolytic capacitor replacement, panel lamp replacement, power circuit tap change, 100V specification change, each input/output operation check)
Accessories: instruction manual (copy)
Main specifications: input terminals Phono 1, 2, AUX, tuner, tape 1, 2, 3 output terminals PRE OUT1, 2, TAPE OUT1, 2, W406 x H138 x D330 mm 11.8 kg
This is PLATANUS MC type phono cartridge. The connection from deep bass to high frequencies is good, and the playback ability is delicate and has a sense of density. You can honestly feel the vivid, dynamic sounds, and even the performer's emotions, and the records you've listened to over and over again until now will play richer and more beautiful music. Magnetic circuits are precision machined and integrated from large chunks of pure iron to enhance rigidity so that vibration energy from the needle tip to the power generation coil is not damaged. The printing has disappeared, and there are small scratches on the body, but the needle tip is good (Sasaki Shota)
Maintenance information: 2024.6.3 operation confirmed
Accessories: original box, manual
Main specifications: Playback frequency 10 to 50,000 Hz impedance 2.5 ohms dead weight 16 g
Full maintenance was carried out to replace all deteriorated parts such as capacitors and vacuum tubes! 38 FD, the most popular of the 38 series, is now in stock! The warm tone has plenty of warmth in the bass and mids, and you can enjoy the true essence of lackstone, where you can enjoy the afterglow of the tone. The exterior has a beautiful finish due to exterior maintenance, but rust etc. on the back remain. Serial 101 20007 (Tomoho Asaine)
Maintenance information: 2024.6.6 maintained (parts replacement, input/output waveform check, load test (1kHz sine wave, 8Ω load: 30W+30W, OK), sound output test) 2020.4.2 maintained (vacuum tube (50CA10), electrolytic capacitor, block electrolytic capacitor, coupling capacitor, vacuum tube socket, headphone jack, micro switch, rectifier diode, semi-fixed resistor, fuse replacement. Complete disassembly of SW/VOL contacts, polish, and apply grease to prevent oxidation and sulfidation. Circuit readjustment, input/output waveform confirmation, load test (1kHz sine wave, 8Ω load: 30W+30W), distortion adjustment (maximum output: 0.2%), sound output test)
Accessories: manual copy power cord
Main specifications: 30W+30W (4, 8, 16 ohms) line input 4 systems phono 2 systems (mm) W476 x H190 x D335 mm 18 kg
The price has been drastically reduced. 2024/5/26 sales price 278,000 yen Maintenance and cabinet repair completed! This is a full set that combines 33 QUAD original transistor preamps and 303 power amplifiers with tuner FM3. Comes with a wood case that allows 33 and FM3 to be built in parallel. The impression is that the natural atmosphere has definitely increased, and the glossy way it rides and the sound that goes through the core make you think it's a vacuum tube amplifier (Oikawa Tetsuji)
Maintenance information: 2024.5.4 maintained (internal check, power supply, filter C, HPX circuit C, etc., there are many differences in capacity → replacement f cover misalignment → readjust, tuning indicator lamp back change, DIN SP-RCA female cable damaged → created)
Accessories: power cable, connection cable (2 types: DIN-RCA and DIN-DIN types), copy of the instruction manual, FM coaxial connector
Main specifications: external dimensions W550 x H113 x D220 mm, weight approx. 7.0 kg (actual measurement) [33] 3 input/line systems, 1 phono system (MM) [FM3] tubular FM dedicated tuner with automatic stereo/mono switching
2018 fully restored item. This model omits the MC step-up transformer. The rear speaker terminal has also been changed to one compatible with banana plugs to match modern usability. Although it is a model from the 60s, there is no sense of a faded sound, and it feels like the flat, thick lackstone has been revived energetically. The sound without getting tired even after listening to it for a long time makes me fully experience the luster and warmth of stringed instruments. There are stains all over the exterior, and there are line scratches, fading, etc. on the cabinet (Sasaki Shota)
Maintenance information: 2018.8.25 Maintained (9P socket, SP terminal, RCA terminal, block capacitor, volume/BAL/TCVR, semi-fixed resistor, coupling capacitor, AC cord, resistor replacement. Power SW contact deterioration prevention relay added. SW/VR disassembly, cleaning, solder correction. (Internal and external cleaning, circuit readjustment, waveform check, input/output check, load test, sound output test)
Accessories: copy of instruction manual
Main specifications: output 10W+10W input terminal AUX1 · 2 Phono 1 · 2 (mm) W470 x H175 x D275 mm weight 14 kg
2018 fully restored item. This model omits the MC step-up transformer. The rear speaker terminal has also been changed to one compatible with banana plugs to match modern usability. Although it is a model from the 60s, there is no sense of a faded sound, and it feels like the flat, thick lackstone has been revived energetically. The sound without getting tired even after listening to it for a long time makes me fully experience the luster and warmth of stringed instruments. There are stains all over the exterior, and there are line scratches, fading, etc. on the cabinet (Sasaki Shota)
Maintenance information: 2018.8.25 Maintained (9P socket, SP terminal, RCA terminal, block capacitor, volume/BAL/TCVR, semi-fixed resistor, coupling capacitor, AC cord, resistor replacement. Power SW contact deterioration prevention relay added. SW/VR disassembly, cleaning, solder correction. (Internal and external cleaning, circuit readjustment, waveform check, input/output check, load test, sound output test)
Accessories: copy of the manual
Main specifications: output 10W+10W input terminal AUX1 · 2 Phono 1 · 2 (mm) W470 x H175 x D275 mm weight 14 kg
The price has been reduced! 2024/6/15 Sales price 248,000 yen Manufacturer maintained! 20th anniversary model. It's an excellent player with excellent sharpness and high resolution. Equipped with the mechanism VMK-5! It has excellent quietness and enables accurate reading. The amount of information is also high, the sharpness is good, and you can enjoy realistic sound images. Serial 90030 (Fujisawa Yukishi)
Maintenance information: 2024.6.15 manufacturer maintained (mechanical parts, remote control battery box replacement. Mechanical ASSY disassembly/cleaning/lubrication clamper mechanism partial disassembly/rework correction repair carried out. Turntable height adjustment implemented. Each part was inspected and operation confirmed)
Accessories: remote control, instruction manual, power cord
Main specifications: VRDS-NEO (VMK-5) equipped with Cirrus Logic 24 bit/192 kHz/CS4398 in a dual mono configuration Word sync terminal dimensions W442 x H153 x D353 mm weight 17 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/2/16 sales price 378,000 yen ※The power supply section has been newly created. Other internally deteriorated parts have been restored! 2-way 100Hz specification An electric crossover coveted by Mark Levinson fans. You can see how well the early Levinson was built can be seen from the feel of the knobs that seem to make you addicted. You can listen closely to Levinson's unique sounds even on Divider. The exterior has scratches on the front top plate and other threads (Mizusaki Ryo)
Maintenance information: 2024.2.16 Maintained (*Since there is no power source, new power supply and connection cable were manufactured, noise appears in the LChLow output, transistor defects in the low pass module were replaced, re-encapsulated, readjusted due to left and right level differences, 4 volume contacts were cleaned, specs were inspected, and blocking characteristics were inspected. The crossover is 100Hz)
Accessories: Power supply unit (newly created, non-genuine), power cable, copy of instruction manual
Main specifications: 2 way (100 Hz specification) closed module type RCA Remo input/output size (main unit) W483 x H51 x D156 mm 2.8 kg size (power supply part) W101 x H101 x D256 mm 2.2 kg
The disposal price has been reduced! (Member price not applicable) 2024/5/26 sales price 298,000 yen Current belt drive type player equipped with Luxman's original tonearm. Dust coverless specification The high initial motion sensitivity unique to knife-edge bearings, stable trace performance, and excellent sound quality delivered from a machined aluminum heavyweight platter are attractive. Despite its compact size, you can enjoy authentic analog sound. The appearance is good with little feeling of use. Serial M21000149 (Tomoho Asaine)
Maintenance information: 2024.5.26 Operation confirmed
Accessories: instruction manual, power cord, original box, shell screwdriver, 2 hex wrenches, handles
Main specifications: belt drive system PID controlled brushless DC motor 33 1/3 rpm, 45 rpm, 78 rpm switchable static balance, S-shaped universal type knife edge structure compatible cartridge dead weight 4 to 10 g (17 to 23 g including attached headshell) anti-skating 0 to 4 g W465 x H133 x D393 mm weight 15.8 kg
Maintained by the manufacturer! Remote control is missing. The highest-end model of Denon's integrated CD player. The relaxed low range makes you feel analog sound quality. The operation of loading a stabilizer with a strong sense of weight is unique to top loading. The exterior has a feeling of use over time, such as dullness and small scratches. Serial 6031501867 (Hiroki Aso)
Maintenance information: 2024.6.4 maintained (tray opening/closing SW disassembly, contact cleaning laser pickup RF level check (however, repairs will not be possible if sound skips in the future or failure such as not reading TOC due to the disc), inspection of each part, operation test)
Accessories: instruction manual stabilizer original box
Main specifications: 2 analog outputs, 3 digital outputs, 2 digital inputs, W434 x H164.5 x D395 mm, 20 kg
Maintained! A regular Yamagiwa model. It is a hidden popular model as the successor to the C26. It is an amplifier from the golden age of McKinn that is highly popular with music fans, with a sound reminiscent of a rich, thick vacuum tube sound. It makes vintage speakers sound intense. The exterior has paint floats, rust spots, etc. Serial BV1675 (Murakoshi Yoichi)
Maintenance information: 2024.6.21 maintained (each SW, VOL cleaning, lamp deterioration replacement, pin jack cleaning, earth plating wire treatment, poor push button SW contact → dismantling cleaning, operation check (gaps cannot be completely removed))
2022.2.4 Maintained (replaced due to poor noise compared to power circuit transistors. Electrolytic capacitor replacement. Selector switch contact cleaning contact grease application. Replace a dead lamp. The RCA terminal plating has peeled off and deteriorated, so it was replaced. (Each input/output operation test)
Accessories: instruction manual (copy)
Main specifications: input PHONO 1 · 2, AUX 1 · 2, TUNER, TAPE 1 · 2 W435 × H188 × D395 mm 11.8 kg
A special edition model commemorating the 70th anniversary of JBL's founding. The latest version that has been refined over the traditional 4312 series. A 12-inch diameter woofer unit equipped with the advanced 4429 is used. It is an all-round speaker with a sense of energy and good range extension. The exterior has dullness, small scratches, and threads. Serial 00687/00688 (Yonejima Satoshi)
Maintenance information: 2024.6.11 sweep test good
Accessories: saran net
Main specifications: 3-way bass reflex type 300mm woofer 125mm mid-range 25mm tweeter impedance 6Ω output sound pressure level 90dB frequency characteristics 44Hz to 40kHz W362 x H597 x D298 mm 25.2 kg
2023 Maintained! One of the best masterpieces of pre-main amplifiers in SANSUI history. It's powerful, with a sense of extrusion, and makes you hear a stretchy and expansive sound. The deep sinking low frequencies and the good tone unique to MOS are some of the best finished premains in SANSUI history. As for the exterior, there are scuffs and line scratches on the top plate. Serial 606068517 (Yonejima Satoshi)
Maintenance information: 2023.6.23 maintained (power supply circuit part rectifier diode replacement, transistor, resistor exchange, indicator lamp replacement, protector part transistor replacement, output relay, headphone relay replacement, power amplifier part solder repair, rec selector, power amplifier direct switch disassembly, polishing grease application, each volume, switch cleaning, internal inspection and cleaning, SP terminal correction, adjustment, operation confirmation. (*There is some hardness on the SP terminal)
Accessories: instruction manual
Main specifications: effective output 150W+150W (6Ω) 110W+110W (8Ω) W450 × H176 × D486mm 32.1 kg
This is a standard JBL monitor that has undergone internal and external maintenance and has been refreshed. The darker and thicker tone compared to the current model still doesn't even seem to be declining in popularity. The thick, exhilarating sound goes well with jazz and rock, and the punchy sound becomes a habit. The exterior is in a beautiful state due to maintenance. Serial 32648 32951 (Yamato Yuki)
Maintenance information: 2024.6.7 operation confirmed
2021.10.15 Maintained (exterior cleaning/repair saran frame painting/net replacement cone paper touchup/tweeter grill dent correction ATT cleaning unit detachable)
2012.1.27 Maintained (ATT replacement, capacitor replacement, input/output waveform and balance check, sound output check, frequency characteristic measurement, front baffle repair (touch-up painting), exterior cleaning, plate attachment (not completely flat because there were already quite a few wrinkles)
Sound output test)
Accessories: saran net
Main specifications: 3-way 3-speaker bass reflex system frequency characteristics 45 Hz to 20 kHz sound pressure level 93 dB impedance 8 ohms allowable input 100 W dimensions W362 x H597 x D298 mm weight 20 kg/1
Maintained! Comes with a remote control. A CD player developed to commemorate the 100th anniversary of Philips's founding. The sound is soft and relaxed, and the thickness of the analog-like mid-low range is particularly irresistible. A swing-arm CDM-4 mechanism is used for the mechanism part, and TDA1547 (DAC7) is used for the D/A conversion part to achieve advanced S/N improvements. As for the exterior, there are bald spots and stains on the SW area. MZ019204080075 (Tamura Eiji)
Maintenance information: 2024.6.9 Maintained (both tray slide belt and CD standby motor belt replaced. Other CD mechanisms, drive circuit check, reading check OK, remote control check OK)
Accessories: remote control, lock pin
Main specifications: CDM-4 mechanical DAC7 equipped analog output 2 systems (XLR/RCA) 2 digital output systems (optical/coaxial) W457 x H140 x D359 mm 16.7 kg
Maintained! An FM masterpiece arm made in Japan made with a high level of stainless steel and workmanship accuracy. The clear, thick tone that doesn't make you feel incidental sounds is excellent, and the breadth and ease of settings, and the excellent firm and excellent tracing ability in the dynamic balance type are excellent (Oikawa Tetsuji)
Maintenance information: 2024.6.5 Maintained (We will disassemble the arm needle pressure application mechanism part and clean it. The arm lifter skate rubber was replaced due to deterioration. Operation tests with cartridge mounting were also good)
Accessories: phono cable, instruction manual
Main specifications: total length 325 mm effective length 245 mm overhang 15 mm needle pressure application range 0 to 5 g arm height adjustment 25 to 60 mm compatible cartridge weight (including shell) 17 to 44 g mounting hole diameter 31 mm
Fully restored! A kit model of a power amplifier using a 50CA10 3-pole output tube and an OY15 type output transformer, composed of circuits and parts conforming to the MQ60 type, which has been evaluated by LUXMAN. The sound of a vacuum tube has a sense of volume that seems to meet expectations, and it gently envelops you. The sound, which doesn't require scale, is particularly unique, and the slight thickness that spreads from below the mid-range makes you feel comfortable. The exterior is dull, rust, abrasions, etc., and there is a feeling of use (Ryo Mizusaki)
Maintenance information: 2024.6.21 Maintained (vacuum tube sockets, block capacitors, electrolytic capacitors, oil capacitors, SP and RCA terminals, semi-fixed VR, fuse holder replacement. Load test (8Ω load 1kHz 24.5W+24.5W), input/output waveform confirmation, impedance switching SW/gain VOL disassembly contact refinement, oxidation and vulcanization prevention grease coating. Input/output waveform confirmation, load test (1 kHz sine wave, 8 ohm load: 28 W+28 W, actual measurement), sound output test)
Accessories: copy of instruction manual
Main specifications: 30W+30W 50CA10 push pull W410 x H160 x D205 mm 13.8 kg
A model that inherits the lineage of 4312. The sense of speed and range has been improved with a completely renewed unit, and it has been transformed into a high-fidelity speaker that can play all kinds of sources with a clean sound with good damping. There is a light thread on the top of the exterior. Serial 13466 13432 (Murakoshi Yoichi)
Maintenance information: 2024.6.6 sound output confirmed
Accessories: saran net
Main specifications: 3-way 3-speaker bass reflex impedance 6 ohms playback frequency band 45 Hz to 35 kHz output sound pressure level 93 dB size W362 x H597 x D299 mm weight 17 kg
The disposal price has been reduced! (Member prices are not applicable) 2023/6/24 sales price 178,000 yen Maintenance has been carried out and deteriorated capacitors etc. have been replaced! A newly created power supply is included. Genuine RF MC cartridge head amplifier. The RCA terminal specification makes it easy to use, and has a separate power supply structure. The delicate, clear, and powerful sound is attractive (Daiki Goto)
Maintenance information: 2023.6.24 maintained (new power supply manufactured because the power module is defective but cannot be repaired, all deteriorated capacitors replaced, pin jack deterioration replaced, gain changeover switch replaced due to poor contact, each gain readjusted, operation inspected, (there are no current problems with the module)
Accessories: copy of instruction manual
Main specifications: Gain can be adjusted in 3 levels; input impedance can be used up to 45 ohms W175 x H60 x D210 mm 1.4 kg
Comes with original box This model was developed based on the 2.0S design concept of the company's higher-level model. The sound has good visibility across the entire band, has a solid sense of density, and has an excellent sense of air. Both stylus and cantilever are good (Oikawa Tetsuji)
Maintenance information: 2024.6.3 operation confirmed
Accessories: original box, instruction manual
Main specifications: MC type 0.4 mV impedance 4 ohms needle pressure 1.9 to 2.2 g dead weight 12 g
A new standard model for the SL-1200 series, inheriting the efforts and results that began with the development of the SL-1200G. Outstanding reliability and stability are now available at an affordable price. I'm also happy that it is compatible with 78 revolutions. There are small scratches and threads on both the body and dust cover on the exterior (Mizusaki Ryo)
Maintenance information: 2024.6.7 operation confirmed
Accessories: instruction manual, power cord, RCA cable, earth cable, original box, subway, shell
Main Specifications: Direct Drive Turntable System Brushless DC Motor Speed 33 1/3, 45, 78 Universal S-shaped Tone Arm Static Balance Needle Pressure Adjustment Range 0 to 4 g Applicable Cartridge Weight/5.6 to 12.0 g, 14.3 to 20.7 g (including headshell) /when using auxiliary weight/10.0 to 16.4 g, 18.7 to 25.1 g (headshell included) W453 mm x H173 mm x D372 mm approx. 11.5 kg
Maintained by Luxman! This model is a return to Luckstone, which is reminiscent of the tube ball era. By changing from pure A grade up until then to grade AB, the sense of extrusion is prioritized, and the corners of the high range are rounded up to give the mid to low frequencies a sense of volume. It has excellent sharpness, and I would recommend this amplifier to almighty music fans. On the exterior, there are dirt scratches, threads, and peeling on the veneer sheet. Serial W90712062H (Tamura Eiji)
Maintenance information: 2024.6.14 Maintained by the manufacturer (power supply part, fuse broken replacement. Install the volume and fix it. Output relay contact fault replacement. Meter lamp replacement. Power supply unit, diode replacement. Replace the amplifier section and semi-fixed volume for adjustment. Board solder correction. volume, switch contact cleaning. Remote control replacement (Internal cleaning, general cleaning)
Accessories: remote control, power cable
Main specifications: 70W+70W W467 x H179 x D440 mm 19 kg
Maintained! Following the technology at the time of development of the advanced C-2302, a balanced configuration was adopted for the advanced α-X circuit and power supply unit. The sense of strength and driving power of the highest class as a premain is attractive. The exterior is scratched on the side panel, and there is dullness on the front (Mizusaki Ryo)
Maintenance information: 2024.6.21 maintained (power amplifier direct, etc., switch disassembly polishing grease application (input selector, source direct, tape, reck-out, tone, turnover, muting, loudness, processor, subsonic, MM/MC switch), output relay, headphone relay replacement, power amplifier circuit transistor, adjustment volume replacement, solder repair, Interior and exterior cleaning, DC, bias adjustment, operation check. (Clean the mounting screws)
Accessories: copy of instruction manual
Main specifications: 160W+160W (8Ω) 190W+190W (6Ω) phono equipped with advanced α-x balance circuit (MM/MC switching) dimensions W460 x H161 x D446 mm weight 33 kg
The price has been reduced. 2024/6/18 sales price 138,000 yen manufacturer maintenance completed! Luxman primen amplifier. It is an excellent unit with a fine mid-range unique to pure Class A amplifiers. Even difficult sources such as string music, female vocals, etc. are played in a glamorous manner. There is a feeling of use due to appearance, dullness, paint deterioration, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.6.18 Maintenance completed (phono changeover switch/cartridge switch disassembly and cleaning, cleaning of other contacts, solder correction and readjustment, contact cleaning because the turnover switch is out of stock ※ there is some noise at present)
Accessories: copy of instruction manual
Main Specifications: 50W+50W (8Ω) Class A Operation DuoBeta Circuit S Pre-heating Function Line Phase Sensor Mount Frequency Characteristics 10 to 100 kHz Dimensions W453 x H174 x D460 mm Weight 21.4 kg
Maintained! A famous instrument and the first generation preamp. The coat is different from modern tones, and the solid sharpness and punchy tone go great with vintage speakers such as JBL. The crunchy sound image and exhilarating sounds are a habit. The exterior is dull and has a feeling of use. Serial E6T080 (Hiroki Aso)
Maintenance information: 2024.5.27 Maintained (contact push switch due to poor contact with the rotary switch due to poor contact, all switches dismantling contacts polishing contacts grease coating TONE switch disassembly contacts cleaning contacts grease coating electrolytic capacitor replacement lamp replacement each input/output operation check)
Accessories: instruction manual copy power cable (general-purpose product)
Main specifications: 3 phono systems (with head amplifier), line 3 systems, tape, 3 systems, dimensions W445 x H160 x D373 mm, weight 13.4 kg
The price has been drastically reduced! 2024/5/12 sales price 148,000 yen A new standard model for the SL-1200 series that inherits the efforts and results that began with the development of the SL-1200G. Outstanding reliability and stability are now available at an affordable price. I'm also happy that it is compatible with 78 revolutions. There is a thread on the dust cover on the exterior (Satoshi Yonejima)
Maintenance information: 2024.5.12 operation confirmed
Accessories: power cord, connection cord, EP adapter, subway, original box
Main Specifications: Direct Drive Turntable System Brushless DC Motor Speed 33 1/3, 45, 78 Universal S-shaped Tone Arm Static Balance Needle Pressure Adjustment Range 0 to 4 g Applicable Cartridge Weight/5.6 to 12.0 g, 14.3 to 20.7 g (including headshell) /when using auxiliary weight/10.0 to 16.4 g, 18.7 to 25.1 g (headshell included) W453 mm x H173 mm x D372 mm approx. 11.5 kg
Maintained LINN network audio player with integrated amplifier. The built-in amplifier makes it easy to use, and you can easily enjoy network audio. It sounds soft and natural, and is perfect for those who want to enjoy music casually. There are threads and dullness throughout the exterior (Mizusaki Ryo)
Maintenance Information: 2024.6.21 Maintained
Accessories: remote control, power cord
Main specifications: Compatible audio files FLAC, ALAC, WAV, AIFF, AAC, MP3 compatible sampling frequencies 7.35k, 8k, 11.025k, 12k, 14.7k, 16k, 22.05k, 24k, 29.4k, 32k, 44.1k, 48k, 88.2k, 96k176.4k, 192 k compatible bits 16 - 24 bit input terminal Ethernet analog audio RCA x 3 front AUX x 1 MM Phono digital audio coaxial RCA (SPDIF) x 3 TOSLINK (Optical) x 3 output terminal SP terminal 100W+100W W381 x H80 x D355 mm weight 5.0 kg
The price has been drastically reduced! 2024/6/12 sales price 148,000 yen 2023 maintenance completed! A refined version of PHILIPS's core model LHH500. The range has also been expanded, and I have acquired the ability to reproduce a wide sound field, such as an orchestra. You can enjoy Philips sound at an affordable price, and this model is also recommended for those looking for a mid-range CD player. The exterior has small scratches, dullness, and bumps. Serial MZ009345050128 (Yonejima Satoshi)
Maintenance Information: 2023.7.4 Maintained (CD standby motor belt, tray slider motor belt replacement. Replace 5 tact switches. Reading check. (Internal and external co-cleaning)
Accessories: remote control, copy of instruction manual, replacement screws for transport lock pins (only 1)
Main specifications: CDM-4 mini die-cast mechanism, analog output, RCA/2V balance, 3V digital output, coaxial/optical power consumption approx. 17W, W457 x H140 x D359 mm, 16.7 kg
Digital breakout cable sold separately is included. High end AD/DA converter compatible with maximum sample rate PCM768 kHz and DSD 11.2 MHz. In addition to being an excellent USB-DAC, this extremely powerful high-output headphone amplifier that is compatible with balanced driving demonstrates more power than its size. It is also equipped with a high-resolution display, so you can enjoy music both audibly and visually. There is a slight thread on the exterior (Mizusaki Ryo)
Maintenance information: 2024.6.1 operation confirmed
Accessories: manual, original box, power adapter, conversion connector (digital breakout cable)
Main specifications: audio interface, maximum sampling frequency PCM768kHz, DSD 11.2 MHz, output impedance: 200 Ω balanced, 100 Ω unbalanced
Maintained in March 2024! A prime amplifier developed during the heyday of CDs and gained popularity. The powerful, punchy sound quality, which combines the quality of the mid-high range with the power of the low frequencies, is attractive. There is room not found in lower models, and you can enjoy the sound with a sense of scale typical of SANSUI. As for the exterior, there is a scratch on the top plate. Serial 611088582 (Tomonori Asane)
Maintenance information: 2024.3.21 maintained (tone and other switches dismantled and polished with grease applied (turnover, subsonic, muting, loudness, processor, input selector, reck-out, power supply direct, source direct, tape, MM/MC changeover switch), power amplifier, power circuit transistor, resistor, adjustment volume, diode replacement, solder repair, each volume, switch Cleaning, output relay, headphone relay replacement, DC, bias adjustment, interior and exterior inspection cleaning, operation confirmation)
Accessories: instruction manual
Main specifications: Advanced α-X circuit equipped with 160W+160W (8Ω) damping factor 150 (8Ω) Phonomm/MC compatible W460 x H159 x D446 mm weight 33 kg
※The cantilever is slightly tilted to the right. It is a universal specification that can be used with normal arms. Tuned based on EMT professional cartridges. A Vandenhall stylus is used. The sharp low range and the thick, powerful mid-high range are attractive (Murakoshi Yoichi)
Maintenance information: 2024.6.12 sound output confirmed
Accessories: none
Main specifications: output voltage 0.15 mV (1 cm/sec 1 kHz) needle pressure 2.0 to 3.0 g playback frequency band 15 to 25,000 Hz channel separation 25 dB compliance 15 x 10-6 cm/dyne internal impedance 24 Ω needle tip super oval dead weight 17.5 g
The price has been drastically reduced. 2024/6/6 sales price 148,000 yen Manufacturer maintained! Accuphase CD player. It is a CD player developed by introducing technology cultivated with separate systems, DP-80L/DC-81L. You can hear a sound with clear outlines and high transparency, just like the Accuphase from the 90s. There are many line marks, other small scratches, and a feeling of use on the top surface. Serial D0Y305 (Murakoshi Yoichi)
Maintenance information: 2024.6.4 manufacturer maintenance (tray opening/closing belt set and buffer spacer, operation switch, phase and capacitor replacement. Disassembly and cleaning of the loading mechanism. Operation, characteristic tests, aging tests, readjustment of parts, interior and exterior cleaning, insulation, and safety tests)
Accessories: remote control, instruction manual (copy)
Main specifications: 18-bit DAC, 2 analog outputs, 2 balanced outputs, 2 digital output systems, W475 x H115 x D325 mm, 14.5 kg
Maintained! The first α907 model. The alpha series has the highest overwhelming power and amount of information in the series, yet enhances the texture of the mid to high range. Due to Sansui's unique α-X balance circuit, it is an attractive car with a high sense of signal and a clear outline. There are scratches, dullness, etc. on the exterior. Serial 64611138 (Jun Tamai)
Maintenance information: 2024.6.21 maintained (switch disassembly/polishing/grease application (tone, turnover, source direct, subsonic, muting, loudness, processor, power amplifier direct, MM/MC, input selectors) output relay headphone relay replacement bias adjustment volume replacement solder repair/main volume/other volume switch cleaning interior and exterior Inspection and cleaning DC/bias adjustment operation confirmation)
Accessories: copy of instruction manual
Main specifications: effective output 190W+190W (6Ω) 180W+180W (8Ω) damping factor 100 (6Ω) W448 × H160 × D441 mm 28.0 kg