SAEC ceramic shell A beryllium copper washer and a three-point crimping system are used at the arm joint. The overhang can be adjusted by means of a slide plate on the top. There is a cloudy part (Daiki Goto)
Maintenance information: 2024.6.6 continuity confirmed
Accessories: none
Main specifications: sintered aluminum oxide body, 3-point crimping type, weight 18 g
A popular SME classic headshell with a stylish design. It's lightweight, which is essential for light needle pressure arms and heavy cartridges, and after all, this is the best fit for SME arms (Mizusaki Ryo)
Maintenance information: 2024.6.6 continuity confirmed
Accessories: none
Main specifications: aluminum stamping dead weight 8g
Line transformer from Uesugi Laboratory. By sandwiching it between the digital device and the amplifier, the characteristic digital noise that causes listening fatigue is removed. You can expect a change in sound quality that is familiar to the ear. It is possible to switch between 3 types of input impedances. There are scratches on the exterior. Serial 057 (Tamura Eiji)
Maintenance information: 2024.6.6 operation confirmed
Accessories: none
Main specifications: impedance compatible with 3 RCA input systems 200 ohms: 200 ohms 500 ohms: 500 ohms W175 ✕ H150 ✕ D115mm 2.5 kg
Maintained, with remote control! A famous direct drive machine representative of Technics. The torque is high, the start and stop times are extremely short, and the stable operation that immediately enters constant speed is unique. It also drives LP heavyweights without difficulty. There are small scratches and dullness overall (Oikawa Tetsuji)
Maintenance information: 2024.6.4 Maintained (Electrolytic capacitors were replaced due to faulty capacitors in the power supply unit and motor unit)
Accessories: power supply unit, remote control, copy of instruction manual
Main specifications: Direct drive aluminum die-cast turntable 33, 45, 78 rotating body W365 x H100 x D360 mm 9.5 kg power supply unit W110 x H85 x D300 mm 3.8 kg
Maintained! An FM masterpiece arm made in Japan made with a high level of stainless steel and workmanship accuracy. The clear, thick tone that doesn't make you feel incidental sounds is excellent, and the breadth and ease of settings, and the excellent firm and excellent tracing ability in the dynamic balance type are excellent (Oikawa Tetsuji)
Maintenance information: 2024.6.5 Maintained (We will disassemble the arm needle pressure application mechanism part and clean it. The arm lifter skate rubber was replaced due to deterioration. Operation tests with cartridge mounting were also good)
Accessories: phono cable, instruction manual
Main specifications: total length 325 mm effective length 245 mm overhang 15 mm needle pressure application range 0 to 5 g arm height adjustment 25 to 60 mm compatible cartridge weight (including shell) 17 to 44 g mounting hole diameter 31 mm
*Although it is a 60 Hz specification, the strobe on the platter is 50 Hz. Maintained! It is a setup that successfully combines the stickiness and guts of the classic Grace arm 545 with few quirks, and the delicate expression with fine grain. It's a car that can be enjoyed regardless of genre. The exterior and flash are not compatible with 50 Hz specifications, and a feeling of use can be seen on the back, such as screw holes, dullness, abrasions, scratches, etc. that seem to be numerous hinge installation marks. Cereal 69774 (Kobayashi Hitoshi)
Maintenance information: 2024.6.5 maintenance completed (motor disassembly/check/lubrication/assembly, motor suspension rubber replacement, suppressor → rebuild replacement, main bearing disassembly/oil filling, oil sealant application, assembly, pulley adjustment, idler cleaning, TT mat replacement, mount rubber washer added, running test OK)
Accessories: sub weight, black weight
Main specifications: GRACE G-545: static balance type effective length 237 mm cartridge mounting weight range 9.5 to 34 g (including shell) needle pressure variable range 0 to 5 g GARRARD 301: idler drive compatible with 33, 45, 78 rotations W500 x H210 x D403 mm
Maintained including pickup replacement (replacement)! A CD player that lets you listen to a glossy, supple sound typical of England. It is the first model in the FMJ series, which continues with the CD36, which aims for a modern approach while retaining the core part of traditional English traditions. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.6.4 maintenance (replacement of products that can be replaced with pickups, mechanical assy cleaning, grease up of various parts) 2024.5.5 operation confirmed
Accessories: remote control, instruction manual, power cord
Main specifications: Equipped with a “24 bit ring DAC” jointly developed with DCS, HDCD compatible digital output: coaxial/TOS analog output: RCA2 system W430 x H85 x D290 mm 6.5 kg
The disposal price has been reduced. Member prices are not applicable. 2024/6/4 sales price 498,000 yen upgraded product (green display on display). Jeff Roland's classic preamp. It's a supple, mature expression, and you can also listen to the sound of excellent quality. It is an excellent control amplifier that also has the great advantage of being easy to bring to your own favorite sound with accessories such as cables. There are stains all over the exterior, and there is a scratch on the front corner of the top plate (Kojima Yosuke)
Maintenance information: 2024.6.4 operation confirmed
Accessories: instruction manual, power cable, connection cable, conversion plug
Main Specifications: Input: XLR×5/Bypass XLR×1 Output: Main Out XLR×1/Record Out XLR×1 Preamp Part: W445 × H80 × D152.5mm 11kg Power Supply Unit: W445 × H38 × D122 mm 3 kg
The price has been drastically reduced. 2024/6/4 sales price 698,000 yen Oba Shoji genuine 2nd generation mono amplifier equipped with an ultra-high speed switching power supply. The suppleness, delicacy, and strength are all first-class products. First of all, I was surprised by the smooth, cored sound. The driving power is also excellent, and it has the ability to easily drive high-class speakers. There are 2 noticeable paint peeling spots on the top plate and light scuffs and minor scratches in places (Sasaki Shota)
Maintenance information: 2024.6.4 operation confirmed
Accessories: instruction manual, power cable, connection cable
Main specifications: 200W+200W (8Ω) 350W+350W (4Ω) main body W445 × H97 × D335 mm 13.5 kg/unit power supply unit W445 × H97 × D319 mm 13.7 kg/unit
The price has been drastically reduced. 2024/6/4 sales price 1,380,000 yen The piano black is a majestic B&W802 diamond. It is a high-end machine that boasts a clear and transparent high range unique to diamond tweeters, and a medium to low range that is ideal for home environments, achieving both tightness and a sense of volume. There are about 3 thin line wounds on the side (Kojima Yosuke)
Maintenance information: 2024.6.4 operation confirmed
Accessories: instruction manual, saran net, jumpers, casters, spikes, casters (currently attached), transport locks, special wrenches
Main specifications: 3-way bass reflex type 25mm diamond dome tweeter 150mm warven kevlar 200mm loha selcone woofer playback frequency band 27Hz to 33kHz sensitivity 90dB impedance 8Ω crossover frequency 350Hz 4kHz size W368 x H1,135 x D563 mm weight 72 kg/bottle
Maintained! Inheriting the technology of the C-2302Vintage, it is a control amplifier with excellent cost performance. It uses a Teflon board, a phono input compatible with 3 positions, and WBT for input/output terminals, etc., making it a structure unique to SANSUI with no gaps in specification materials or circuit configurations. It has a sharp, clear, and powerful sound. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.6.4 Maintained (INPUT switch, CARTRIDGE switch, MODE switch, other selector switches x 4 disassembly contact polishing. Master volume cleaning. Reinforced power board solder. (General adjustment)
Accessories: copy of the manual
Main specifications: Phonoico built-in control amplifier, MC/MM compatible, 7 input systems, 3 output systems, W460 x H137 x D383 mm, 16.5 kg
The disposal price has been reduced. Member prices are not applicable. 2024/6/4 sales price 780,000 yen A high-performance speaker that condenses the sound production of the multi-cabinet SYSTEM7 into a single cabinet. The balance between dynamism, wide range, and sense of sound localization is excellent. Another advantage is that it creates a sound that is less likely to be affected by the performance of the amplifier. There is a partial tear in the corner of the saran net, and there is a linear paint crack separating the top and bottom on the right side of one (Sasaki Shota)
Maintenance information: 2024.6.3 sweep test is good
Accessories: manual, spike, spike holder, cover
Main specifications: 3-way 4Ω frequency characteristics 29Hz to 22.5kHz 89dB W320 × H1040 × D460 mm 73 kg
Accupase's best model as an integrated player compatible with SACD. It is a best-selling SACD player that inherits the know-how of advanced models. It is delicate, has a sense of scale, and has a large sound field. While it has the amount of information unique to high-end players, the fine particle feel that feels fine against the skin is truly remarkable. There is a scratch on the top plate. Serial D9Y630 (Sasaki Shota)
Maintenance information: 2024.6.3 operation confirmed
Accessories: remote control, manual, power cable
Main specifications: SACD compatible CD player, ultra giter free plus PLL circuit, MDS++ conversion system, D/A converter, HS-Link equipment, frequency characteristics 0.5 to 50 kHz, S/N ratio, 114 dB, W477 x H156 x D394 mm, 27 kg
Luxman's current phono equalizer that uses a non-feedback CR amplifier circuit using an all-stage vacuum tube has arrived! Using vacuum tubes, 4 independent Super Permaloy MC boost transformers and 4 output transformers are mounted on the left, right, and low/high, respectively. It is a model that emphasizes sound quality, using a VU meter and OFC, which are fun to look at. It is one that can be controlled in a variety of ways. There are small wounds and dullness (Sasaki Shota)
Maintenance information: 2024.6.3 operation confirmed
Accessories: original box, manual, power cable
Main specifications: circuit method: SRPP, terminal cathode follower, non-feedback CR type equalizer (RIAA) vacuum tube: ECC83 x 4, ECC82 x 2, EZ81 x 1 input sensitivity (1 kHz, when gain is switched 36 dB): MM 4mV, MC high 0.44mV, MC low 0.18mV input impedance: mm30kΩ to 100kΩ (variable), MC high 40Ω, MC low 2.5Ω gain (1kHz, when gain is switched at 36 dB): mm36dB, MC High55dB, MC Low63dB S/N ratio mm76dB, MC High75dB, MC Low74dB W440 x H92 x D397mm weight 12.5 kg
The price has been reduced. 2024/6/4 sales price 398,000 yen*Inexpensive because there are noticeable scratches on the front. Player system with SME3010R mounted on Luxman PD-171AL! Popular MC cartridge SPUs can also be attached. The combination of the latest high-end machines and high-end arms makes it a player that excels in the amount of information with Japanese precision and a reliable skeleton. It is one that brings out the characteristics of cartridges to the greatest extent with precise sound (Oikawa Tetsuji)
Maintenance information: 2024.6.3 operation confirmed
Accessories: power cable, instruction manual
Main specifications: [PD-171AL] belt drive AC synchronous motor quartz lock oscillator amplifier turntable · machined aluminum surface finish · diamond cut weight 5.0 kg rotation speed 33 · 45 rpm W492 ✕ H140 ✕ D407 mm weight 23.8 kg
Comes with original box It is an MC cartridge that uses diamond star rice chips and boron cantilevers, which are also used in higher-level models, and is characterized by outstanding high-pitched fineness and clear sound quality even in the same price range. Both the cantilever and stylus are good (Oikawa Tetsuji)
Maintenance information: 2024.6.3 operation confirmed
Accessories: original box, instruction manual
Main specifications: moving coil type, 4 ohm, needle pressure, 1.7 to 2.0 g, output voltage 0.3 mV or more, playback frequency 10 Hz to 30 kHz, solid boron, cantilever, machined aluminum, body, diamond stylus tip, 10.5 g
This is PLATANUS MC type phono cartridge. The connection from deep bass to high frequencies is good, and the playback ability is delicate and has a sense of density. You can honestly feel the vivid, dynamic sounds, and even the performer's emotions, and the records you've listened to over and over again until now will play richer and more beautiful music. Magnetic circuits are precision machined and integrated from large chunks of pure iron to enhance rigidity so that vibration energy from the needle tip to the power generation coil is not damaged. The printing has disappeared, and there are small scratches on the body, but the needle tip is good (Sasaki Shota)
Maintenance information: 2024.6.3 operation confirmed
Accessories: original box, manual
Main specifications: Playback frequency 10 to 50,000 Hz impedance 2.5 ohms dead weight 16 g
Comes with original box This model was developed based on the 2.0S design concept of the company's higher-level model. The sound has good visibility across the entire band, has a solid sense of density, and has an excellent sense of air. Both stylus and cantilever are good (Oikawa Tetsuji)
Maintenance information: 2024.6.3 operation confirmed
Accessories: original box, instruction manual
Main specifications: MC type 0.4 mV impedance 4 ohms needle pressure 1.9 to 2.2 g dead weight 12 g
Denon high-end MC cartridges in the heyday of analog, using amorphous boron pipes. A sound with a wide range and good separation, which has a different trend from the standard 103 series. This is the reference cartridge at the time. Both the cantilever and stylus are good (Oikawa Tetsuji)
Maintenance information: 2024.6.3 operation confirmed
Accessories: none
Main specifications: MC type output 0.2 mV 40 ohm boron cantilever solid diamond special oval needle playback band 20 to 75 kHz proper needle pressure 1.0 to 1.4 g dead weight 5.8 g
A small but authentic pre-main amplifier with a built-in FM/AM tuner. Comes with PHONO input (MM/MC), so you can enjoy analog well. It's a perfect match for those who can't play very loudly or for second systems. There are no major noticeable scratches on the main body, but there is corrosion on the battery part of the remote control (Oikawa Tetsuji)
Maintenance information: 2024.6.3 operation confirmed
Accessories: remote control, power cable
Main specifications: 75W+75W (8Ω) 150W+150W (4Ω) MC/MM compatible AM/FM tuner built-in W300 x H80 x D341 mm 5.5 kg
※There is no problem with operation, but since it has an air freshener smell, it is inexpensive and is currently sold. A speaker developed in collaboration with European sound designers. It is compact, has good sound, and the soft, gentle treble characteristic of soft dome tweeters is attractive. A model with a wooden cabinet with a calm design that is excellent for space harmony. There are no major scratches that are particularly noticeable on the exterior (Oikawa Tetsuji)
Maintenance information: 2024.6.3 operation confirmed
Accessories: jumper cable
Main specifications: 2 way 2 speakers bass reflex type anti-magnetic design (JEITA) 13 cm cone type carbon fiber woofer 2.5 cm/ soft dome type tweeter impedance 6 Ω output sound pressure level 86 dB dimensions W182xH296xD293 mm weight 8.7 kg/1
Unused item! (Opened to confirm continuity) Power transformer primary: 100-105-110V secondary: 22-25V/AC5.5A x 2 (Bridge DC3.2A), 5.5V/AC1A x 2 W120 x H140 x D100mm 5.5 kg original box, with instructions, fixed stay, and fixing nut (Kojima Yosuke)
Accessories: original box, manual, fixed stay, fixed nut
Unused item! (Opened to confirm continuity) Power transformer primary: 100-105-110V secondary: 22-25V/AC5.5A x 2 (Bridge DC3.2A), 5.5V/AC1A x 2 W120 x H140 x D100mm 5.5 kg original box, with instructions, fixed stay, and fixing nut (Kojima Yosuke)
Accessories: original box, manual, fixed stay, fixed nut
Output transparent sale Orient core output 38W for push pull applications: 6CA7, 6GB8, etc. Primary: 5 kΩ Secondary: 4-6-8-10-16 Ω W118 × H104 × D118 mm approx. 4.5 kg/piece (actual measurement, not including protrusions) There are abrasions and stains in places (Kojima Yosuke)
Accessories: none
※The top surface is severely damaged, so it is inexpensive. This is a custom-made model that fits the size of Acoustic Revive's popular RSS series 4-legged speaker stand to LAT-2. Of course you can use it with other speakers if the size fits (Ryo Mizusaki)
Accessories: spike holder
Main specifications: W300 x H610 x D400 mm top plate W280 x D360 mm 28.5 kg/1 bottle (actual measurement)
Although the details of the stand are unknown, it is well-made, and it is a silver iron stand.
It has a simple appearance, so it can be used for a variety of purposes. The exterior has noticeable dirt on the bottom plate and support (Mizusaki Ryo)
Accessories: none
Main specifications: height: 625 mm top plate size W145 x D180 mm bottom plate size W250 x D310 mm weight 5 kg/1 bottle
High output type. You can easily enjoy the delicate sound of MC cartridges without a step-up transformer. The thick mid-range, and the instantaneous, and light sound is attractive. Serial 4875 (Murakoshi Yoichi)
Maintenance information: 2024.6.2 sound output confirmed
Accessories: original box
Main specifications: high output MC type, output voltage 1.6 mV, needle pressure 1.5 to 2.1 g, playback frequency band 20 to 45,000 Hz, load resistance 47 kΩ or more, internal impedance 160 Ω, needle tip 0.1 x 0.2 mm square solid, special elliptical needle, dead weight 4.8 g
The price has been drastically reduced! 2024/6/4 sales price 79,800 yen The Silver series is used in woofers that use the new DCF technology. The unit, which has the familiar high-speed texture, is stored in a relatively large enclosure. The low range, which has more volume than the size, and the clear mid to high range are attractive. The exterior has a feeling of use such as dullness. Cereals (Tomoho Asaine)
Maintenance information: 2024.6.3 sound output confirmed
Accessories: jumper cable (general purpose)
Main specifications: 2-way bus reflex type frequency characteristics 40 Hz to 35,000 Hz, crossover frequency 2,800 Hz, efficiency 88 dB, impedance 8 ohms, W230 x H375 x D329 mm, weight 9.3 kg/unit
Maintained! A late model in the classic 607 series. It has high-resolution, well-defined sound, and is compatible with modern speakers. You can experience SANSUI's ability. There are threads and small scratches (Daiki Goto)
Maintenance information: 2024.6.2 maintained (maintenance contents/TONE and other subsonic, loudness, processor, muting, source direct, power amplifier direct, input selector, tape switch disassembly, polishing grease application, output relay replacement, protector capacitor replacement, each volume, switch cleaning, pin jack polishing, internal inspection and cleaning, running test.)
Accessories: copy of the manual
Main specifications: 105W+105W (6Ω) 90W+90W (8Ω) phono MM/ MC switching W430 x H162 x D452 mm 18 kg
Comes with original box First arrival at Hi-Fi Hall. Headphones with a focus on sound and design. You can enjoy it regardless of genre with clear lines of sound. It is characterized by being comfortable to wear without the impression that it is being compressed. It is in good condition (Sasaki Shota)
Maintenance information: 2024.6.2 operation confirmed
Accessories: manual, original box, connection cable
Main specifications: diamic sealed 40mm driver frequency characteristics 20 to 22 kHz impedance 30 ohms cord length 1.2 m 230 g
※There is no problem with operation, but since it is cheap, it will be handed over as is. A small 2-way speaker with excellent sense of localization and transparency. The high frequency that extends smoothly is easy on the ears, and although it is a basic model, it has a solid musical sound, which is attractive. There is a stain on the saran net on the exterior (Mizusaki Ryo)
Maintenance information: 2024.6.1 sound output confirmed
Accessories: none
Main specifications: 2 way 2 speakers rear bass reflex frequency band 53 Hz to 26.5 kHz crossover 2.9 kHz 6 Ω 86.5 dB W162 x H274 x D228 mm 4.2 kg
Sold per bottle, rectifier tube, GZ37 equivalent tube, made in England, measured value 62 (rejected value 40) with original box ※The measured value shows the gM value measured with the test machine TV-7 (Kojima Yosuke)
Accessories: original box
Sold per bottle, rectifier tube, GZ37 equivalent tube, made in England, measured value 62 (rejected value 40) with original box ※The measured value shows the gM value measured with the test machine TV-7 (Kojima Yosuke)
Accessories: original box
Single sale rectifier tube GZ37 equivalent tube heat pipe made in England measured value 64 (rejected value 40) with original box ※The measured value shows the gM value measured with the test machine TV-7 (Kojima Yosuke)
Accessories: original box
Single sale rectifier tube GZ37 equivalent tube heat pipe made in England measured value 64 (rejected value 40) with original box ※The measured value shows the gM value measured with the test machine TV-7 (Kojima Yosuke)
Accessories: original box
Pair tube, 5 pole tube, smoke mesh plate, made in England, measured value 34/34 (rejected value 25) with white box ※Pairs are determined based on gM values measured with the test machine TV-7 (Kojima Yosuke)
Accessories: white box
Pair tube, 5 pole tube, smoke mesh plate, made in England, measured value 36/36 (rejected value 25) with white box, so it's inexpensive because it makes a rattling noise in 1 tube ※Pairs are determined based on gM values measured with the test machine TV-7 (Kojima Yosuke)
Accessories: white box
Pair tube, 5 pole tube, smoke mesh plate, made in England, measured value 40/40 (rejected value 25) with white box ※Pairs are determined based on gM values measured with the test machine TV-7 (Kojima Yosuke)
Accessories: white box
Sold per bottle, rectifier tube, GZ37 equivalent tube, made in England, measured value 62 (rejected value 40) with original box ※The measured value shows the gM value measured with the test machine TV-7 (Kojima Yosuke)
Accessories: original box
It is a grace shell characterized by a fin shape. Lightweight yet hard, highly rigid shell (Asaine Tomoho)
Maintenance information: 2024.6.2 continuity confirmed
Accessories: No accessories
Main specifications: carbon fiber dead weight 10.7g
Hi-Fi is in stock for the first time! GLANTZ statically balanced tone arm. The main body is machined from hard stainless steel, and the structure is firmly supported by 4 large bearings, and it has high traceability performance with reduced resonance and blurring, and exudes a sharp sound. Since there is weight in the weight part, you can use heavy cartridges such as OrtoFon's SPU without lowering the weight too much. The exterior is generally good (Takahashi Nobuyuki)
Maintenance information: 2024.6.2 operation confirmed
Accessories: instruction manual, headshell, phono cable, cartridge installation screw wrench
Main specifications: Form Static balance system Total length 330 mm Effective length (arm fulcrum to needle tip) 305 mm Effective length (arm fulcrum to center of turntable) 290 mm Compatible cartridge 16 to 43 g weight 1.14 kg Overhang 15 mm Mounting base internal dimensions 16 mm Mounting hole 30 mm
The price has been reduced! 2024/6/2 sales price 118,000 yen ROYAL AUDIO TSB-9 with dedicated stand! A popular Pioneer ribbon tweeter. A golden combination of beryllium diaphragms and alnico magnets. In addition to the ultra-high frequency sound quality correction, the expansion of spatial expression, and the wide sound field can be clearly experienced with classical sources. The exterior is dull, and there are scratches on the front mesh and pedestal (Takahashi Nobuyuki)
Maintenance information: 2024.6.2 operation confirmed
Accessories: dedicated stand
Main specifications: input impedance 8 ohms, playback frequency band, 5,000 Hz to 120,000 Hz, maximum input, 100 W, output sound pressure level, 97.5 dB, crossover frequency of 5,000 Hz or more, W134 x H89 x D179 mm, 2.6 kg
※It is inexpensive because there are many scratches on the whole. Although it is small, it is an attractive car with a low range and medium to high range with a solid core in the middle. Bi-wire compatible It is compatible with a wide range of genres, and is recommended not only for pure audio but also for surround sound (Ryo Mizusaki)
Maintenance information: 2024.6.1 sweep test is good
Accessories: nothing
Main specifications: Bi-wiring compatible anti-magnetic design impedance 6 ohms playback frequency band 33 Hz to 45 kHz output sound pressure level 88 dB dimensions W194 x H326 x D318 mm weight 8.4 kg
Digital breakout cable sold separately is included. High end AD/DA converter compatible with maximum sample rate PCM768 kHz and DSD 11.2 MHz. In addition to being an excellent USB-DAC, this extremely powerful high-output headphone amplifier that is compatible with balanced driving demonstrates more power than its size. It is also equipped with a high-resolution display, so you can enjoy music both audibly and visually. There is a slight thread on the exterior (Mizusaki Ryo)
Maintenance information: 2024.6.1 operation confirmed
Accessories: manual, original box, power adapter, conversion connector (digital breakout cable)
Main specifications: audio interface, maximum sampling frequency PCM768kHz, DSD 11.2 MHz, output impedance: 200 Ω balanced, 100 Ω unbalanced