Video digital cable, 1.0m, RCA terminal, SP-LGC conductor, entry model for the company's digital cable. There is a big difference in sound just by replacing it with a general-purpose digital cable (Kojima Yosuke)
Accessories: original box
Pair tube ambient heat beam tube made in America, measured value 42/40 (rejection value 25) with original box (the claws on one side of the box are missing) *Pairs are determined based on gM values measured with the test machine TV-7 (Kojima Yosuke)
Accessories: original box
MC cartridge using LC-OFC (linear crystal/oxygen-free copper) wire based on DL-103. Familiar sound with a wide range. The supple sound makes it comfortable to listen to. The exterior has a feeling of use, such as dullness on the body. Serial 4126 (Hiroki Aso)
Maintenance information: 2024.4.21 sound output confirmed
Accessories: none
Main specifications: MC type output 0.25 mV, proper needle pressure 2.2 to 2.8 g, internal impedance 13 ohms, own weight 8.5 g
Genuine wood wax for TANNOY speakers. Approximately 10% have been used. Since fixation due to aging can be seen, quality cannot be guaranteed (Hiroki Aso)
Accessories: original box
This is a model with PAD cryo treatment applied to the TOSHIBA 3P/2P conversion adapter. There are some cracks, but they are glued together (Oikawa Tetsuji)
Maintenance information: 2024.4.20 continuity confirmed
Accessories: none
※1 bottle only. TOA large metal radial horn. In terms of sound quality, it has a narrower impression than Altec's sectional horn 311, but it has a bright sound with a sense of overhang unique to radial horns. *The diameter of the mounting hole seems to be slightly smaller than ALTEC, so there is a possibility that ALTEC's 1.5-inch drivers will not fit depending on individual differences. Overall, there are wounds, dullness, etc. (Oikawa Tetsuji)
Accessories: none
Main specifications: cross 500 Hz or more, horizontal 90 degrees, vertical 40 degrees, throat diameter 35.5 mm, compatible driver HFD-651, width 720 mm, height 220 mm, depth 580 mm, 10.9 kg
Maintained by the manufacturer! 4th generation of the DENON 2000 series. It is an amplifier that can be enjoyed regardless of the genre of music, with its plump, loud mid and low frequencies, and a pleasant, sharp tone. The exterior has dents in the upper right corner of the front, light line scratches in the lower left corner, and dullness throughout (Kanai Hidetsugu)
Maintenance information: 2024.4/18 manufacturer maintenance (disassembling the switch, polishing the contact, grease coating, idling adjustment, operation test)
Accessories: instruction manual, power cord
Main specifications: High-rigidity 6-block, separated chassis, power amplifier, direct input, bi-wiring compatible, 80W+80W, W434 x H180 x D478 mm, 23.5 kg
*The headshell is an SPU-G (M) one, but the body is inexpensive because it is GE. Needle cover missing. G-shell oval needle model. The glossy, rich, and heavy sound is attractive without fading. It is an eternal staple cartridge that fully conveys the original appeal of analog. The exterior has rust on the metal parts, and dullness and dirt throughout the body. The needle tip is in good condition (Murakoshi Yoichi)
Maintenance information: 2024.4.17 sound output confirmed
Accessories: none
Main specifications: G shell oval needle MC type output 0.2 mV needle pressure 3 to 4.5 g internal impedance 2 ohms dead weight 31 g
The price has been drastically reduced. 2024/4/19 sales price 698,000 yen Maintained in 2023! Hammer tone BBC specification! Strobe platter included! This is a combination of GARRARD 301 and SME 3009S2, which has an attractive gripping, and gutsy sound. The high sensitivity short arm with high utility and the sound produced from the idler turntable is exhilarating and very comfortable. It is a record player system that allows you to experience the true essence of analog. Since the shaft on the back of the motor is long, an Audio-Technica insulator is included. *Currently, the pulley is 60 Hz, but the strobe platter is for 50 Hz (Murakoshi Yoichi)
Maintenance information: 2023.8.15 maintenance (motor disassembly/check, lubrication, assembly. Main bearing disassembly, cleaning, oil injection, oil sealant application, assembly. Overall cleaning. idler cleaning. Motor suspension spring rubber replacement. Transport plate fixing clip. Linguage distortion correction. Noise suppressor rebuild replacement. Mount rubber washer added. 50Hz pulley adjustment added. SME3009S2 cleaning. Mount grommet replacement Contact cleaning. (Running test)
Accessories: insulator (audio technica AT616)
Main specifications: 301: idler drive 33, 45, 78 rotations compatible 3009S2: short arm static balance type, total length 265 mm, overhang 15 mm, needle pressure (when 1 rider weight is attached) 1 memory 0.25 g step 0 g to maximum 2.5 g (when 2 rider weights are attached) 1 memory 0.5 step 0 g to maximum 5 g cartridge dead weight up to 28 g size W480 x D406 x H238 mm weight 12.5 kg
Pair tube large transmission tube direct heat triode tube made in China gold base gold foot measured IP value 47mA/47ma (the best standard IP value for this amplifier is 50mA) with original box (part of the box is damaged) *Sound is checked with a test amplifier, plate current values have been measured, and it has been determined that operation is good (Kojima Yosuke)
Accessories: original box
Input transformer pair sale primary impedance 600 Ω (150 Ω split) secondary impedance 600 KΩ (150 kΩ split) primary inductance 70H W50 × H70 × D57 mm 0.75 kg/piece (actual measurement, not including protrusions) The badge is discolored, and there are scratches in places (Kojima Yosuke)
Accessories: specifications
Full internal and external maintenance completed in 2022! This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. In particular, it works great with vacuum tube amplifiers, and the sense of orchestra scale and smooth playback of stringed instruments are satisfying enough to listen to. The exterior has some impact scratches and board repair marks on one side of the hakama part. Serial 003354/003047 (Fujisawa Yukishi)
Maintenance information: 2022.9.23 Maintained (terminal screws, rust removal, acid washing, cleaning. Internal connection terminal (faston) replaced with a new one. ATT (SW type) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check the input/output waveform and balance, and check the sound output. Unit maintenance (high range side: magnetic circuit gap cleaning/center adjustment) exterior repair/polishing/oil finish. Front and rear baffles/hakama repair/painting Saran net replacement)
Accessories: saran net
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
Denon's classic shell. This is a genuine DA-305 shell. There is also plenty of room around the lead wire, and various cartridges can be attached. There is a feeling of use on the exterior such as small scratches and dullness (Tamai Jun)
Maintenance information: 2024.4.19 sound output confirmed
Accessories: none
Main specifications: dead weight 7g
Speaker cable, 5,0m pair, untreated ends, an introductory cable that is soft and easy to run. The medium range is easy to hear and has a sense of volume, making it perfect for upgrading from accessories. The exterior has a feeling of use such as dullness (Tomoho Asaine)
Maintenance information: 2024.4.19 continuity confirmed
Accessories: none
This is a genuine shell that comes with the DP-1300M/DP-500M. Black model with meat removal processing. The exterior has a feeling of use such as dullness (Tomoho Asaine)
Maintenance information: 2024.4.19 sound output confirmed
Accessories: none
Line transformer using TANGO's input transformer, NN-600-600. The overall sound resolution is increased, and the sense of sound pressure is also enhanced. Recommended for those using speakers with horn drivers. TANGO badges are discolored, and there are tape marks and bumps on the chassis (Kojima Yosuke)
Maintenance information: 2024.4.18 Operation confirmed
Accessories: none
Main specifications: primary impedance 600 Ω (150 Ω split) secondary impedance 600 KΩ (150 kΩ split) primary inductance 70 H W140 × H110 × D100 mm 1.8 kg (actual measurement, not including protrusions)
*Needle cover missing. G-shell elliptical needle model. The glossy, rich, and heavy sound is attractive without fading. It is an eternal cartridge that fully conveys the appeal of analog. There are slight corrosion irregularities on the shell (Murakoshi Yoichi)
Maintenance information: 2024.4.17 sound output confirmed
Accessories: none
Main specifications: G shell oval needle MC type output 0.2 mV needle pressure 3 to 4.5 g internal impedance 2 ohms dead weight 31 g
The price has been reduced. 2024/4/18 sales price 600 yen Nagaoka record cleaner using Italian velvet. The exterior shows a feeling of use such as dullness, etc., and wear on the velvet (Asaine Tomoho)
Accessories: none
The price has been reduced! 2024/4/18 sales price 500 yen*It's cheap because it deteriorates drastically! Audio-Technica record cleaner. High-grade velvet can be used to clean records gently and effectively. It's also perfect for those just starting to arrange records. The exterior shows a feeling of use such as dullness, etc., and wear on the velvet (Asaine Tomoho)
Accessories: none
Internally and externally maintained! This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. In particular, it works great with vacuum tube amplifiers, and the sense of orchestra scale and smooth playback of stringed instruments are satisfying enough to listen to. The exterior has been beautifully finished due to exterior maintenance. Serial 011093 016017 (Tomonori Asaine)
Maintenance information: 2024.4.18 Maintained (exterior repair/polishing/oil finish front and rear baffle/hakama repair/paint saran frame reinforcement painting/net replacement, batch polishing unit maintenance (high frequency magnetic circuit/in-gap cleaning/center adjustment diaphragm gap indirect attachment) ATT cleaning unit detachable)
Accessories: saran net
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
This is a woofer mount adapter that is thought to be used to convert a 38cm unit hole to a 30cm unit. The previous owner attached it to the JBL C38 BARON. The exterior and bolt mounting part of the individual on one side are damaged, and there is a feeling of use due to dullness, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: mounting screw pitch: outer circumference: 370 mm, inner circumference: 293 mm; caliber: 270 mm; external dimensions: W356 x H365 x D10 mm; approx. 0.4 kg
Maintained by the manufacturer! This model was the first to use an ALPHA processor in the best-selling 1650 series. The mid and low frequencies are quite stable, and the balance depicts rich, rich music regardless of genre. The exterior has dents on the front panel corner, and there are line scratches, small scratches, dullness, etc. ※The remote control is out of stock (Oikawa Tetsuji)
Maintenance information: 2024.4.17 manufacturer maintained (inside the CD mechanism, loading belt, tray opening/closing SW replacement. VR has been reworked. The HF waveform of the laser pickup is within the regulations and is currently fine. Sound output test)
Accessories: copy of instruction manual ※ remote control missing
Main specifications: Real 20-bit 4DAC/Lambda Super Linear Converter with 20-bit 8x oversampling digital filter+GIC 3rd order analog filter frequency characteristics 2Hz to 20kHz W434 x H120 x D340 mm 10.2 kg
The price has been drastically reduced. 2024/4/17 sales price 128,000 yen Maintained! Quad control amplifier The famous machine 44 has been refreshed by changing the back terminal to an RCA specification that is easy to handle. It's a perfect balance between freshness and richness. When paired with speakers made in England, you can enjoy a calm, high-quality sound (Daiki Goto)
Maintenance information: 2024.4.17 maintained (internal all checks, B-filter capacitor deterioration, +- 18V drive Tr leak large, rectifier diode failure instability → replacement power SW spark killer broken → replacement. C and R checks within each board. *There is a sound leak at main volume 0. (Create 2 1.5m DIN5 cables)
Accessories: copy of instruction manual, power cable, connection cable
Main specifications: 2 LINE inputs, 1 PHONO input, 1 phono sensitivity, 1m/3m/10mV switching, W321×H103×D203 mm
The price has been reduced. 2024/4/17 sales price 34,800 yen ※Currently sold. Fidelity-Research's standard model for light needle pressure. The simple design is also beautiful, and you can enjoy high-quality analog sound at an affordable price. Inside Force Canceller B is out of stock
Maintenance information: 2024.4.13 sound output confirmed
Accessories: phono cable
Main specifications: static balance type short arm, effective length 245 mm, needle pressure range 0 to 3 g
The price has been reduced! 2024/4/16 sales price 24800 yen ※It is cheap because it has a cigarette smell. Since it is 120V specification for commercial use, it will be handed over as is. A compact commercial power amplifier that is highly regarded as a professional studio monitor amplifier. The driving power that cannot be imagined from its size is truly the real thrill of a professional aircraft. The range is reasonable, but it is characterized by a sound image that does not lose sound even at high volumes. There are scratches on the exterior. Serial 8001337592 (Tamura Eiji)
Maintenance information: 2024.4.16 Operation confirmed
Accessories: none
Main specifications: 40W+40W (8Ω) W483 x H44.5 x D213 mm 4.5 kg
Full maintenance from capacitor replacement to re-soldering of each board, etc.! The first memorable luxury model in the Sansui 07 series in the era when there was no 907. Starting with the newly developed dual FET at the time, the company's consistent commitment to adopting quadruple detent volumes and large electric power transformers independently on the left and right has already been established. Compared to models from the 80s and 90s, the sense of fulfillment in the phono section is amazing. There is a feeling of use due to appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.16 Maintained (capacitor, semi-fixed resistor, transistor, resistor, protection relay SP terminal, heat dissipation sheet replacement. SW type terminal cleaning, contact grease coating. Re-solder flux cleaning for each board. Each circuit adjustment, RCA terminals, interior and exterior cleaning. (Various tests)
Accessories: copy of instruction manual
Main specifications: 85W+85W W430 x H168 x D389 mm 16.8 kg
Speaker cable A standard BELDEN speaker cable nicknamed “sea snake” with an unprocessed 1.7 m pair end. The cable braided in orange and black is impressive, and it features a tight sound. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.14 continuity confirmed
Accessories: none
The disposal price has been reduced (member prices are not applicable). 2023/11/26 Sales price 128,000 yen Maintained in 2022/6! An eye-catching power amplifier with its black and large power meter typical of Sansui. It entertains me with its power, which can be felt from its appearance, and its supple, stretchy sound quality. The exterior has dullness, scratches, rust, etc. over time (Oikawa Tetsuji)
Maintenance information: 2022.6.23 Maintained (both channel volumes replaced. SP relay bad contact replacement. Replace protectors, deteriorated transistors, resistors, and diodes in meter boards. Replace deteriorated transistors and resistors in the power supply board. Replace deteriorated transistors and capacitors in the drive board. OUTPUT selector switch cleaning. (General adjustment)
Accessories: none
Main specifications: left and right independent 2 power supply diamond differential circuit effective output 110W+110W (8Ω) load impedance 4 to 16 ohms W482 x H187 x D450 mm 20.3 kg
※The veneer is peeling, the top plate is undulating, and the grill is indented, so it is inexpensive. This high CP model was released in the 49th year of Diatone's founding. It has a very well-balanced, rounded, and gentle tone. I can do everything from jazz and rock to classical and pop music as an all-rounder (Oikawa Tetsuji)
Maintenance information: 2024.4.15 Operation confirmed
Accessories: none
Main specifications: 3 way 3 speakers, 6.3 ohms, sound pressure level, 90 dB, W380 x H680 x D295 mm, weight 25 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/4/14 sales price 198,000 yen This model takes the configuration of the flagship 7S1. The quality of the sound has improved compared to the predecessor, and in particular, the thickness of the sound has increased from low to medium, making it a well-balanced sound. The clear and clean spatial expression and smooth, gentle mid-high sound are attractive. There is a scratch on the top plate. Serial 20011208001208 (Fujisawa Yukishi)
Maintenance information: 2024.4.14 Operation confirmed
Accessories: remote control, instruction manual, power cord, connection cord
Main specifications: original mechanical module SACDM-1 1 bit DSD SEIKO NPC SM5866AS D/A converter with external clock terminal W440 x H127 x D413 mm 16.5 kg
Speaker cable A standard BELDEN speaker cable nicknamed “sea snake” with an untreated 1.0 m pair end. The cable braided in orange and black is impressive, and it features a tight sound. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.13 continuity confirmed
Accessories: none
Speaker cable A standard BELDEN speaker cable nicknamed “sea snake” with an untreated 0.6 m pair end. The cable braided in orange and black is impressive, and it features a tight sound. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.13 continuity confirmed
Accessories: none
Speaker cable A standard BELDEN speaker cable nicknamed “sea snake” with an untreated 0.5 m pair end. The cable braided in orange and black is impressive, and it features a tight sound. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.13 continuity confirmed
Accessories: none
The price has been reduced. 2024/4/14 sales price 79,800 yen LE8T's ancestral 20cm cone type full range unit that makes the most of the basic design of the D130 in a small caliber. It's small and has a cute appearance, but the bright, clear, and tense sounds make you feel like JBL from the good times. In addition to leaving small repair marks on the exterior and part of the cone, there is a feeling of use such as dullness, sticking marks, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.11 Maintained (cone repair)
Accessories: none
Main specifications: 20cm cone type full range unit, allowable input 30W, 8Ω, 97dB (1kHz), recommended enclosure, internal volume: 42L to 113L, depth: 76mm, weight: 2.3 kg
The price has been drastically reduced! 2024/4/13 sales price 79,800 yen Maintained! Audionics of Oregon power amplifier RF regular, 117V specification In Japan, it is an American manufacturer imported by R.F. Enterprises under the name Audio of Oregon. A thick, low center of gravity sound with a punchy sound. It is an American sound suitable for jazz and rock. It can also be used as a mono power amplifier. There are exterior, dullness, small scratches, scratches on the top plate, etc. ※The plug has been changed. (YONEJIMA Satoshi)
Maintenance information: 2024.4.13 Maintained (main amplifier circuit resistor replacement. Idling current misalignment adjustment. (Distortion level check)
Accessories: No accessories
Main specifications: 170W+170W (2Ω) 120W+120W (4Ω) 70W+70W (8Ω) 225W (8Ω, when connected to BTL) AC117V 50Hz/60Hz dimensions W483 × H89 × D216 mm weight 7.7 kg
Maintained. Elliptical type with built-in step-up transformer. It has a rich, rich sound and sounds like an SPU. Clarity has been improved by incorporating a transformer that creates a well-balanced sound. Although it is an MC type, it can be used in the MM position. The exterior has dirt, sticker marks, dullness, and a feeling of use (Katsuji Hiura)
Maintenance information: 2024.4.13 Maintained (broken cantilever, damper adjustment, vibration system replacement)
Accessories: original box needle cover
Main specifications: MC type transformer built-in elliptical needle output 10 mV playback frequency band 20 to 20,000 Hz needle pressure 3 to 4.5 g dead weight 32 g
Maintained. Elliptical type with built-in step-up transformer. It has a rich, rich sound and sounds like an SPU. Clarity has been improved by incorporating a transformer that creates a well-balanced sound. Although it is an MC type, it can be used in the MM position. The exterior has small scratches, dullness, and a feeling of use (Katsuji Hiura)
Maintenance information: 2024.4.13 Maintained (broken cantilever, damper adjustment, vibration system replacement)
Accessories: original box needle cover
Main specifications: MC type transformer built-in elliptical needle output 10 mV playback frequency band 20 to 20,000 Hz needle pressure 3 to 4.5 g dead weight 32 g
The price has been drastically reduced. 2024/4/11 sales price 118,000 yen ※It's cheap because it doesn't have a hood. Maintained! Vacuum tube stereo power amplifier. The bright and fresh sound typical of DYNACO is attractive. This is an amplifier I want to play in combination with JBL, Altec, etc. The grill is missing, and there is a feeling of use due to aging (Daiki Goto)
Maintenance Information: 2024.4.11 Maintained (· Block Capacitor 30/20/20 μF Defect Replacement · Stereo/Mono Switch Defect Replacement · Shock Noise Improvement Measures → Spark Killer Addition · Vacuum Tube 7199 Noise Exchange · Mylar Capacitor 390pF Deterioration Replacement 2 · Resistors 1/2 W Deterioration Replacement · BIAS Readjustment · Vacuum Tube Socket and RCA Jack Caulking Repair. *Other operation checks have been performed (measured at 32 to 41 W SP: 8 Ω at rated output AC 100 to 117 V)
Accessories: instruction manual
Main specifications: rated output 35W+35W vacuum tube EL34 x 4 7199 x 2 GZ-34 x 1 W330 x H165 x D240 mm 12.5 kg
Speaker cable A standard BELDEN speaker cable nicknamed “sea snake” with an unprocessed 1.1 m pair end. It is a cable with thickness and a sense of extrusion in the mid-range (Murakoshi Yoichi)
Maintenance information: 2024.4.7 continuity confirmed
Accessories: none
Nagaoka record cleaner. High-density velvet fits the sound groove of the record board and removes dirt. As for the exterior, there are dirt and scratches on the case (Tomoho Asae)
Main specifications: body dimensions W115 x D42 x H35 mm 40 g (actual measurement)
※ The stylus is a genuine SHURE VN35HE. The lock on the needle cover doesn't work, so it's cheap. Good needle tip! It combines the delicate expressive power unique to light needle pressure with an energetic, thick sound typical of Type 3. Recommended for those who listen to jazz and rock (Daiki Goto)
Maintenance information: 2024.4.10 operation confirmed
Accessories: none
Main specifications: mm type frequency range 10 Hz to 25,000 Hz output voltage 3.5 mV needle pressure 0.75 g to 1.25 g weight 6 g
The disposal price has been reduced. Member discounts are not applicable. 2024/4/10 sales price 238,000 yen Maintenance completed! A control amplifier representing the golden age of Macintosh. Compared to the C28, this model has a wider range and more subtlety. The rich, glossy, and thick tone is alive and well, especially with vintage speakers. There is rust on the exterior, top plate, and sides, and there is a feeling of use such as dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.10 maintenance completed (each SW, VOL cleaning, pin jack cleaning, lamp deterioration replacement, bridge diode deterioration replacement, pattern re-soldering, connector direct soldering, glass panel peeling correction, operation check)
Accessories: copy of instruction manual
Main specifications: frequency characteristics 20 Hz to 20 kHz input terminals PHONO 1 · 2, AUX, TUNER, TAPE 1 · 2 W406 × H138 × D330 mm 8.6 kg
The price has been drastically reduced! 2024/4/9 sales price 99,800 yen with wood horn! Maintained! An integrated mid-range driver unit developed for 3-way use. It's an energetic and clear sound typical of YL. Paint peeling can be seen in places. Serial 751903, 751903 (Fujisawa Yukishi)
Maintenance information: 2024.4.9 maintained (coil roundness adjustment, noise suppression, porcelain circuit slit maintenance)
Accessories: No accessories
Main specifications: Playback frequency band 800 to 8000 Hz maximum input 40 W 8 Ω output sound pressure level 101 dB outer diameter W400 × H200 × D350 mm 3.30 kg
RCA cable, 1.0 m pair, 2-core shield structure, rhodium-plated plug suppresses sound dramatization and reproduces the individuality of the amplifier and player as it is. The plug shell is dull and discolored a lot, and the LR coloring is deteriorated and damaged, so it is inexpensive (Kojima Yosuke)
Accessories: none
Pair tube KT88 compatible ball American metal base measurement value 58/52 (rejection value 44) There is getter burn and loss on one side, and there is dullness on the base on the other side ※The pair is judged based on the gM value measured by the testing machine TV-7 (Kojima Yosuke)
Accessories: none
The disposal price has been reduced. Member discounts are not applicable. 2024/4/9 sales price 138,000 yen ※It is cheap because the condition is not good. Next-generation model of the L-550, a famous pure Class A amplifier that has been maintained by the manufacturer (*PHONO1 cannot be used due to a broken equalizer board). The very smooth, deafening warm color sound perfectly matches the delicate sound quality of pure A grade. It also has a reputation for analog sound, and thick sound quality can be obtained with both MM/MC. There is a feeling of use due to appearance, dullness, abrasions, scratches, paint deterioration, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.9 manufacturer maintenance completed (equalizer selector switch disassembly cleaning, correction due to broken equalizer board, other contact cleaning, general adjustment*PHONO1 cannot be used due to broken equalizer board)
Accessories: copy of instruction manual
Main specifications: pure A grade 50W+50W (8Ω) PHONO (MM/MC) PHONO/CD straight circuit system W453 x H174 x D470 mm weight 20 kg
Pair tube KT88 compatible ball American metal base measurement value 68/62 (rejected value 44) *Pairs are determined based on gM values measured with the test machine TV-7 (Kojima Yosuke)
Accessories: none
The price has been reduced. 2024/4/8 sales price 15,000 yen balance cable 1.5m pair standard AccuPhase balance cable. It is a natural sound that removes disguise to enhance the characteristics of amplifiers and players. On the exterior, the cover at the base of the plug is damaged, and there is a feeling of use such as dullness (Hiura Katsuji)
Maintenance information: 2024.4.8 continuity confirmed
Accessories: none
*There is a gap in the display panel, which is the current situation. This is the model number DCD-1650 gold model representing DENON. Although it is the first model, the sophisticated design is beautiful. There is a sense of transparency in the mid to high frequencies, and the low frequencies are thick and gentle. In terms of functionality, the range of uses has also been expanded, such as installing a program play of up to 20 songs. There is a slight gap left in ATT. Serial 106154518 (Mizushima Itsuro)
Maintenance information: 2018/4/12 manufacturer maintained (pickup, belt, gear, relay replacement. Solder correction, operation confirmation)
Accessories: copy of instruction manual
Key Specifications: 20-bit Lambda SLC-D/A Converter with pitch control W470 x H122 x D360 mm 11.3 kg
NAGAOKA stylus cleaner. This is a standard cartridge cleaner product and an easy to use and convenient item. It's a volatile and safe cleaner. About 80% of the remaining amount is left (Yamato Yuki)