The flagship model of the Macintosh power amplifier with a silver panel. It is characterized by its rich sound. The extrusion is strong and goes great with JBL large monitor speakers. The dynamism in the mid to low range, which is difficult to obtain with current Mackin power amplifiers, is attractive. There are scratches, dullness, and discoloration in places (Kojima Yosuke)
Maintenance information: Maintained on 2020.8.26 (2 input volumes, 4 semi-fixed volumes, 2 RCA plugs, 12 lamps, 8 electrolytic capacitors, replacement input mode switch disassembly cleaning, card edge cleaning, soldering, bias and offset check, output sound check)
(*The interior and exterior have been cleaned.)
Accessories: power cable
Main specifications: 500W+500W (1000W when mono) equipped with power guard circuit W483 x D465 x H263 mm 60.3 kg
Choke transformer 0.9 H/260 mA DC resistance 26.8 ohm (actual measurement) choke transformer mounted on A3600, etc. W55 x H71 x D50 mm 0.7 kg (actual measurement, not including protrusions) There are scratches and paint peeling in places (Kojima Yosuke)
Accessories: none
The disposal price has been reduced. Member prices are not applicable. 2024/5/6 sales price 998,000 yen*The front panel is 20.6L, but it is an upgraded product starting at 20. Maintained! Genuine Harman product. The excellent separation unique to mono and the excellent sense of shading of the sound give off a unique difference, and even large aperture woofers drive well. Also, the slightly sweet, and comfortable sound similar to ML-2L is attractive. It still makes music fans groan. There are scratches and small scratches on the exterior. Serial 666/665 (Sasaki Shota)
Maintenance information: 2024.4.15 Maintained (1 deteriorated transistor has been replaced. Other inspections and adjustments have been made) 2023.7.20 maintained (connector contact between the heat sink board and main board has been corrected. Tr, capacitor and resistor exchange. Part of the board solder is re-soldered. Attach the Fisher plug to the SP cable. (Other inspections and adjustments)
Accessories: copy of instruction manual, power cable, Fisher to SP cable, Remo pin x 2, balance short pin
Main specifications: mono power amplifier effective output 100W (8Ω) input/unbalance (RCA) 1 system, balance (XLR) 1 system, 1 SP terminal system W483 ✕ H210 ✕ D560 mm weight 33 kg/unit
Taok's popular 4-tier audio rack. Strong construction typical of TAOC. It tightens the tone of the audio system. The length of the pole has been changed from the original. Scratches are conspicuous (Daiki Goto)
Accessories: instruction manual
Main specifications: W600 x H920 x D520 pole length 350, 250, 200 mm weight 21 kg (actual measurement)
This is a set of 4 small spikes. It has good cost performance, high rigidity that can withstand a single point load at point contact, and achieves stable point contact. There is a feeling of use on the exterior such as dullness and small scratches (Tamai Jun)
Accessories: none
Main specifications: diameter 20 mm x H9.9 mm 15.8 g (1 piece)
This is a set of 4 small spikes. It has good cost performance, high rigidity that can withstand a single point load at point contact, and achieves stable point contact. There is a feeling of use on the exterior such as dullness and small scratches (Tamai Jun)
Accessories: none
Main specifications: diameter 20 mm x H9.9 mm 15.8 g (1 piece)
The disposal price has been reduced! (Member price not applicable) 2024/4/12 sales price 70,000 yen B&W 805D series speaker stand. Equipped with a spike insulator “T-PROP”. It is a speaker stand with a completely new concept developed with the theme of eliminating speaker stress as much as possible by absorbing and releasing it in a natural way without putting a load on the diamond formation structure. The exterior has scratches, paint peeling, and bumps. (FUJISAWA KOSHI)
Accessories: insulator T-PROP, screws
Main specifications: top plate W227 x D306 mm B&W 805 Diamond, D3 specially designed bottom plate W280 x D360 mm height 500 mm approx. 15 kg
Maintained by the manufacturer! A special edition model of VRDS-10. This is the only TEAC player model that uses a Philips TDA1547 as a D/A converter. The sound quality is not sharp due to the hardware of VRDS, and the sound quality is well-balanced, which brings out the characteristics of the relaxed DAC7. In addition to being able to see many scratches on the exterior and top plate and abrasions on the front panel, there is dullness and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.14 manufacturer maintained (flat cable adjustment) 2024.4.13 manufacturer maintained (belt replacement, deteriorated parts replacement, inspection and adjustment of various parts)
Accessories: remote control, copy of instruction manual, lock key
Main specifications: 2-channel CD player frequency characteristics 1 Hz to 20 kHz 8 times oversampling 20 bit digital filter W442 x H149 x D331 mm 11 kg
Special stand for SX-311GY Chic grey finish It is a model that can be used with various medium speakers. Dullness, small scratches, and abrasions due to aging are conspicuous on the exterior. (YONEJIMA Satoshi)
Accessories: No accessories
Main specifications: W330 x H440 x D294 mm top plate part W267 x D245 mm 5.3 kg
The A3500 vacuum tube power amplifier has been refreshed by thorough maintenance down to the smallest details, such as volume disassembly and polishing. The warm, fresh tone, filled with the appeal of a vacuum tube type, is still appealing enough today. You can enjoy music with a rich, thick tone that contrasts with the clicking tones of recent vacuum tube amplifiers. As for the exterior, paint deterioration and peeling can be seen on the transformer on one side, and there is a feeling of use such as dullness, small scratches, etc., and there is a dent in the hood. ※3-pole tube connection specification. 20W+20W (actual measurement) is output as specified by the manufacturer (Takasaki Atsushi)
Maintenance information: 2023.2.3 maintained (main tube (6CA7) replacement vacuum tube socket, block capacitor, electrolytic capacitor, oil capacitor, SP and RCA terminals, complete disassembly of semi-fixed VR replacement power input gain volume, contact polishing, anti-oxidation/sulfation grease coating load test (8Ω load 1kHz 20W+20W) input/output waveform confirmation sound output check performed)
Accessories: copy of the manual
Main specifications: 20W+20W (8Ω) vacuum tube 6CA7×4/6AQ8×3 W465×H168×D206mm 16kg
Maintained by the manufacturer! The 3rd generation model of the S10 series. Equipped with AL24 Processing, an analog waveform reproduction technology. The degree of perfection of the sound is extremely high, and in addition to the heavy mid-low range, the music is pleasantly enjoyable with colorful tones unique to Denon. There is a feeling of use on the exterior, such as dullness and small scratches. Serial 1021503089 (Yamato Yuki)
Maintenance information: 2024.4.22 Maintained (current laser pickup level is within regulations, but if it breaks down in the future, pickups cannot be obtained. Loading belt tray opening/closing SW replacement sound test)
Accessories: instruction manual copy remote control power cable
Main specifications: 24bit/96kHz alpha processor, HDCD decoder with DA converter function (coaxial/optical switching), W430 x H130 x D330 mm, 14 kg
Set of 4, 32 mm diameter pinpoint base made of African ebony used for oboes, etc. Sound quality can be improved by itself or combined with the PB-10 and placed under a speaker or amplifier. The exterior has a feeling of use such as dullness and scratches (Jun Tamai)
Accessories: original box
Main specifications: load capacity 50 kg (4 pieces) body height 19 mm spike height 5 mm
The disposal price has been reduced! (Member discounts are not applicable) 2024/4/27 sales price 148,000 yen Maintained! It is a model that is small yet has a calm and glossy tone. A combination with European speakers is recommended along with the company's Pre-44. A slightly more modern taste than the 405 has been added. There is a feeling of use on the exterior, such as dullness, small scratches, and peeling paint. Serial Q078428 (Hiroki Aso)
Maintenance information: 2024.4.27 maintained (internal dismantling check, power Tr driver, Tr check, replacement of each C in the board, partial soldering, defect correction, bottom rubber foot mounting operation check)
Accessories: copy of instruction manual DIN to RCA (female) conversion cable, power cable (general purpose)
Main specifications: 100W+100W W341×H115×D195mm 9.0 kg
It has been refreshed and maintained to brush up by replacing block capacitors, etc.! Kit version of the masterpiece model 7. The parts that can be obtained at the beginning of sale remain the original, and those that are missing use similar parts, and it is a 25th anniversary model that appeared with almost the same structure as the original. As a vacuum tube preamp, you can hear a slightly different tone from other models. There are line scratches on the wood case on the exterior. Serial F030105 (Murakoshi Yoichi)
Maintenance information: 2024.5.9 maintenance (main volume disassembly cleaning repair, selector disassembly contact strengthening repair, block capacitor, fuse holder cap replacement, short pin addition, vacuum tube socket and RCA jack re-caulking repair. Operation has been checked with AC100V) In order to bring the volume curve closer to the original, the OUT LEVEL on the back is narrowed down. 2018.7.15 Maintained (vacuum tubes 12AX7 x 2 replaced, oil capacitors 0.47 μF replaced with BlackBeauty, replaced with 0.33 μF x 2 film capacitors. RCA jack earth reinforcement and caulk repair. Vacuum tube socket caulk repair. Other operations have been checked)
Accessories: none
Main specifications: kit model 12AX7 × 6 W453 × H185 × D260 mm 7.9 kg
Maintained! A classic British Quad stereo power amplifier. Small in size yet full torque. The sound, which is as deep as a tube amp, exudes an appeal that won't fade. The exterior has a feeling of use over time, such as dullness and small scratches. Serial 62226 (Yonejima Satoshi)
Maintenance Information: 2024.3.25 Maintained (INPUT DIN 4P replacement, internal Tr, C, R all checks. DIN4P-RCA female cable created. Operation check, pattern solder processing)
Accessories: power cable, connection cable
Main specifications: 45W+45W W120×H159×D324mm 8.2 kg
Set of 4 This stand is made of high-carbon cast iron with excellent vibration handling capabilities. It can be used for a wide range of speakers from large to medium. The sound image is accurately and tightly reproduced. The exterior is dull and has small scratches (Murakoshi Yoichi)
Accessories: none
Main specifications: W100×H140×D300mm high carbon cast iron Weight 8kg/book
There is no problem with the operation, but it will be handed over as is. Yamaha subwoofer. You can easily enjoy powerful sound. The high-cut filter allows you to listen in the desired range, so the range of uses also expands. The exterior has a slightly raised part on the top plate, and there is a scratch on the back corner (Mizusaki Ryo)
Maintenance information: 2024.5.9 sound output confirmed
Accessories: none
Main specifications: A-YST method anti-magnetic amplifier output 250W playback frequency band 20Hz to 160Hz high-cut filter frequency 40Hz to 140Hz continuously variable W340 x H432 x D370 mm 17 kg
The price has been drastically reduced! 2024/4/27 sales price 79,800 yen Maintained! This is the first AUDIO OF OREGON control amplifier to arrive in a long time. It is compatible with 117V specification American speakers such as ALTEC and JBL, etc., and although it is a transistor, it doesn't become too stiff and makes you enjoy the firm sound. The exterior has dullness and scratches. ※The plug has been changed. Genuine RF Serial 02117 (Tamura Eiji)
Maintenance information: 2024.4.27 Maintained (no running symptoms. The board vibration check connection was checked. (All pattern parts of the flat amplifier module unit have been added and soldered.) 2024.4.13 Maintained (Electrolytic capacitor replacement in amplifier module. Pattern contact defect correction. (Voice operation check)
Accessories: No accessories
Main specifications: All stages use pure class A operation circuit input phono (mm/47 kΩ) tuner, tape, aux dimensions W483 x H89 x D190 mm weight 4.5 kg
※1 bottle only. Shorthorn used in the 43 series. It can also be built into an enclosure, but it makes you hear good sound even when attaching a driver and placing it on top of the enclosure. There are paint peeling and scratches on the exterior (Yonejima Satoshi)
Accessories: No accessories
Main specifications: 80 degrees horizontal orientation for 1-inch drivers, 45 degrees vertical, recommended crossover 1.2 kHz, baffle opening diameter 108 mm, depth 216 mm
B&W bookshelf sized speakers It is equipped with a Nautilus tube and Kevlar cone unit from the higher series. This size is sufficient for clean mid to high ranges and low frequencies without any habit. It goes well with modern sauces. The jumper plate is dull, and there is a small scratch on the upper corner (Daiki Goto)
Maintenance information: 2024.5.7 operation confirmed
Accessories: instruction manual
Main specifications: 2 way 16.5 cm woofer 8 ohm bi-wiring connection possible W204 x H356 x D244 mm 6.1 kg
The price has been drastically reduced. 2024/2/18 Marantz pre-main amplifier with sales price 89,800 yen. The preamp circuit has been revamped to enhance spatial expression ability and detail reproducibility. Similar to the PM-10 and PM-14S1, a highly accurate electronically controlled volume is used for the volume circuit. It makes it possible to reproduce bass that combines a sense of scale and instantaneous power. Serial AWY15180500756 There are scratches on the top plate on the exterior (Hiura Katsuji)
Maintenance information: 2024.2.18 Operation confirmed
Accessories: remote control power cable
Main specifications: 100W+100W (4Ω), 70W+70W (8Ω) frequency characteristics 5Hz-100kHz
W440×H128×D379mm 12.0kg
※1 bottle only. A full range unit that combines an aluminum alloy HR diaphragm and a pure magnesium ridge dome diaphragm. Compared to conventional paper units, it has a slightly better transparency and microwave feel. The exterior is stained with corn paper, paint marks and scratches on the frame (Satoshi Yonejima)
Maintenance information: 2024.5.6 sweep test is good
Accessories: original box
Main specifications: impedance 4 ohms minimum resonance frequency 72 Hz playback frequency band F0 to 10 kHz output sound pressure level 85.5 dB
Maintained! Professional crossover 800 Hz network. It's an exhilarating sound with a good view. How about making a 2-way horn system with a 16 ohm unit? In addition to dullness and small scratches on the exterior, there is a feeling of use such as paint peeling. Serial 8091 8074 (Hiroki Aso)
Maintenance information: 2024.5.4 maintained (12 terminal terminal mounting screws, 24 rust and insulation bushings, deterioration replacement. The capacitor used for terminal cleaning is a Dayton attenuator switch contact cleaning crossover 800Hz check red terminal cap partial deterioration replacement)
Accessories: none
Main specifications: crossover frequency 800 Hz impedance 12 to 16 ohms W122 x H154 x D132 mm 1.9 kg/1 unit
Maintained! A network with a crossover frequency of 7000 Hz. Ideal for MID/HIGH use in 3-way systems using the JBL 2420/2440. In addition to dullness and small scratches on the exterior, there is a feeling of use such as paint peeling. Serial 24693 24691 (Hiroki Aso)
Maintenance information: 2024.5.4 maintained (12 terminal terminal mounting screws, 24 insulating bushings replaced for deterioration. The capacitor used for terminal cleaning is a Dayton attenuator VR contact cleaning crossover 7000 Hz check)
Accessories: none
Main specifications: Crossover frequency 7 kHz allowable input (continuous program) 50 W impedance low range 12 to 16 ohms treble range 12 to 16 ohms treble attenuation/variable volume mounting hole W140 x 108 mm 0.7 kg
※Since the cantilever is large and tilts to the right, it is inexpensive. Needle cover missing. The MC30S (MC30 Supreme), the upper model of the MC20S (MC30 Supreme) has a high output of 0.5 mV, which not only has a sense of dynamism and power, but is also characterized by a delicate and elegant high frequency. In classical music such as jazz and rock, there is a sense of depth in the performance, and it stretches well, and you can feel the luster of stringed instruments. There is a feeling of use on the exterior, such as dullness and scratches on the body (Murakoshi Yoichi)
Maintenance information: 2024.5.2 sound output
Accessories: case
Main specifications: MC type output 0.5 mV internal impedance 5 ohms needle pressure 1.8 g to 2.2 g dead weight 10.7 g
Comes with a special bracket. The classic 101 mm small speaker. The sound, which has been compiled in one small full-range shot, makes all kinds of popular music sound cheerfully. The exterior has bumps, scratches, and dullness. Serial 9020409, 9020410 (Fujisawa Yukishi)
Maintenance information: 2024.5.3 operation confirmed
Accessories: special bracket, saran net
Main specifications: 1 way 1 speaker impedance 6 ohms maximum input 150 W output sound pressure level 86 db W232 x H154 x D172 mm 2 kg
Comes with original box! DP-1300M heavy headshell counterweights, set of 2 large and small A must-have item for those using heavyweight cartridges such as SPU and FR. It can also be attached to the DP-500M. It is recommended for those who use a variety of cartridges. There are some scratches on the exterior (Fujisawa Yukishi)
Accessories: original box
Main specifications: Compatible cartridge weight/for 20 to 28 g (small) /26 to 37 g (large)
The price has been reduced! 2024/3/4 sales price 59,800 yen ※The diaphragm has been replaced with a genuine JBL D8R2425. Maintained! Representative of JBL's 1-inch driver units. The playback band is wide, so you can enjoy changing the network cross freely. The toughness, sound pressure, and full-bodied mid-high sound are appealing, which is unbelievable for some input. Scratch marks and paint peeling can be seen. Serial 62206, 62240 (Fujisawa Yukishi)
Maintenance information: 2024.3.4 maintained (diaphragm installation adjustment (diaphragm comes with D8R2425) genuine JBL product. (The pad dampener has been replaced.)
Accessories: No accessories
Main specifications: 1 inch driver, 500 to 20,000 Hz, 8 ohms, W145 x D97 mm, 5.1 kg/bottle
Manufacture-maintained, including pickups. This is the first 1650 limited model equipped with a balanced output similar to the higher-level model. The double chassis structure makes it sturdy. It is a high-density sound, and the thickness of the mid and low tones that cannot be heard with players in the same price range in recent years is attractive. ※The front cover has been replaced with a magnetic one, but a light impact will cause the magnet to come off and open. There are other minor scratches and dullness appropriate to the model year. The remote control is out of stock (Oikawa Tetsuji)
Maintenance information: 2024.4.29 manufacturer maintained (laser pickup, loading belt replacement. Sound output test.
The lower front door did not open due to a bad latch. That's why we're repairing it. The magnet is attached so that it sticks to the metal. Press lightly when closing. (*This is because parts cannot be obtained)
Accessories: copy of instruction manual
Main specifications: Real 20 bit 4DAC Lambda SLC equipped W470 x H122 x D360 mm 12.5 kg
A rare Rotel thin phono equalizer. It has a flat, neutral tone with no distractions, and I like how simple it is to use. There are small scratches, dullness, and the electrical outlet has changed (Oikawa Tetsuji)
Maintenance information: 2024.4.29 Operation confirmed
Accessories: instruction manual, original box
Main specifications: input sensitivity MM: 2.5 mV/47 kΩ MC: 210 mV/100 Ω size W440 × H72 × D195 mm weight 3.1 kg
※Inexpensive because it is in poor condition. Self-made 2way/3way enclosure. The size of the hole is different at the top, with an opening diameter of about 315 mm on the top and about 360 mm on the bottom. There are many peeling veneer, corner pads, scratches, etc. (Oikawa Tetsuji)
Accessories: none
Main specifications: W450 x H1056 x D480 mm approx. 33 kg
The disposal price has been reduced (member prices are not applicable). 2023/11/26 Sales price 128,000 yen Maintained in 2022/6! An eye-catching power amplifier with its black and large power meter typical of Sansui. It entertains me with its power, which can be felt from its appearance, and its supple, stretchy sound quality. The exterior has dullness, scratches, rust, etc. over time (Oikawa Tetsuji)
Maintenance information: 2022.6.23 Maintained (both channel volumes replaced. SP relay bad contact replacement. Replace protectors, deteriorated transistors, resistors, and diodes in meter boards. Replace deteriorated transistors and resistors in the power supply board. Replace deteriorated transistors and capacitors in the drive board. OUTPUT selector switch cleaning. (General adjustment)
Accessories: none
Main specifications: left and right independent 2 power supply diamond differential circuit effective output 110W+110W (8Ω) load impedance 4 to 16 ohms W482 x H187 x D450 mm 20.3 kg
The price has been reduced. 2024/4/6 sales price 69,800 yen This 1-inch screwdriver has been maintained (replaced in pairs with JBL D8R2425 due to a broken diaphragm) and has an impressive high range with a smooth, stretchy high range. Compared to the LE85, you can enjoy a natural sound with a sense of depth. As for the sound of a JBL, I get the impression that it is mild. There is a scuff mark on the back (Daiki Goto)
Maintenance information: 2024.4.6 maintained (diaphragm broken (replaced with diaphragm D8R2425)). Parts replacement DCR (38378/3.2 ohm diaphragm no scratch) DCR (38054/3.1 ohm diaphragm no scratch))
Accessories: none
Key Specifications: 1 inch driver, 8 ohm, crossover, 500 Hz, 108 dB, diameter: 114 x D98 mm, weight: 4.1 kg
Full internal and external maintenance completed in 2022! This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. In particular, it works great with vacuum tube amplifiers, and the sense of orchestra scale and smooth playback of stringed instruments are satisfying enough to listen to. The exterior has some impact scratches and board repair marks on one side of the hakama part. Serial 003354/003047 (Fujisawa Yukishi)
Maintenance information: 2022.9.23 Maintained (terminal screws, rust removal, acid washing, cleaning. Internal connection terminal (faston) replaced with a new one. ATT (SW type) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check the input/output waveform and balance, and check the sound output. Unit maintenance (high range side: magnetic circuit gap cleaning/center adjustment) exterior repair/polishing/oil finish. Front and rear baffles/hakama repair/painting Saran net replacement)
Accessories: saran net
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
Input transformer pair sale primary impedance 600 Ω (150 Ω split) secondary impedance 600 KΩ (150 kΩ split) primary inductance 70H W50 × H70 × D57 mm 0.75 kg/piece (actual measurement, not including protrusions) The badge is discolored, and there are scratches in places (Kojima Yosuke)
Accessories: specifications
Internally and externally maintained! This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. In particular, it works great with vacuum tube amplifiers, and the sense of orchestra scale and smooth playback of stringed instruments are satisfying enough to listen to. The exterior has been beautifully finished due to exterior maintenance. Serial 011093 016017 (Tomonori Asaine)
Maintenance information: 2024.4.18 Maintained (exterior repair/polishing/oil finish front and rear baffle/hakama repair/paint saran frame reinforcement painting/net replacement, batch polishing unit maintenance (high frequency magnetic circuit/in-gap cleaning/center adjustment diaphragm gap indirect attachment) ATT cleaning unit detachable)
Accessories: saran net
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
The disposal price has been reduced. Member discounts are not applicable. 2024/4/9 sales price 138,000 yen ※It is cheap because the condition is not good. Next-generation model of the L-550, a famous pure Class A amplifier that has been maintained by the manufacturer (*PHONO1 cannot be used due to a broken equalizer board). The very smooth, deafening warm color sound perfectly matches the delicate sound quality of pure A grade. It also has a reputation for analog sound, and thick sound quality can be obtained with both MM/MC. There is a feeling of use due to appearance, dullness, abrasions, scratches, paint deterioration, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.9 manufacturer maintenance completed (equalizer selector switch disassembly cleaning, correction due to broken equalizer board, other contact cleaning, general adjustment*PHONO1 cannot be used due to broken equalizer board)
Accessories: copy of instruction manual
Main specifications: pure A grade 50W+50W (8Ω) PHONO (MM/MC) PHONO/CD straight circuit system W453 x H174 x D470 mm weight 20 kg
Maintained by the manufacturer! This model was the first to use an ALPHA processor in the best-selling 1650 series. The mid and low frequencies are quite stable, and the balance depicts rich, rich music regardless of genre. The exterior has dents on the front panel corner, and there are line scratches, small scratches, dullness, etc. ※The remote control is out of stock (Oikawa Tetsuji)
Maintenance information: 2024.4.17 manufacturer maintained (inside the CD mechanism, loading belt, tray opening/closing SW replacement. VR has been reworked. The HF waveform of the laser pickup is within the regulations and is currently fine. Sound output test)
Accessories: copy of instruction manual ※ remote control missing
Main specifications: Real 20-bit 4DAC/Lambda Super Linear Converter with 20-bit 8x oversampling digital filter+GIC 3rd order analog filter frequency characteristics 2Hz to 20kHz W434 x H120 x D340 mm 10.2 kg
Maintained! A 1500 Hz crossover network perfect for combining the LE14A with the 175DLH and LE175. The exterior is dull and has small scratches (Oikawa Tetsuji)
Maintenance information: 2024.4.17 Maintained (2 VR attenuators, 12 screws, 24 insulating washers replaced)
Accessories: none
Maintained. The grain of the sound is clear and the smoothness of the connection has also been improved. This is a 1200 Hz crossover network ideal for the combination of a 38 cm woofer and 1 inch driver. The exterior has dullness and scratches due to use over time, serial 18254 18275 (Asaine Satoshi Law)
Maintenance Information: 2024.4.16 Maintained (Screws, Insulated Washer Parts Replacement Switch Contact Cleaning)
Accessories: none
Key Specifications: Crossover 1200 Hz 8 Ohm 3 Position Switch with Level Control
The disposal price has been reduced. Member discounts are not applicable. 2022/12/18 sales price 79,800 yen Columbia desktop gramophone Viva-tonal Grafonola. You can adjust the volume with the front fins. The sound box is equipped with No. 9. The exterior is in good condition, although there are some scratches and stains due to age, I think it is good considering the age (Kanai Hidetsugu)
Maintenance information: 2022.12.11 sound output confirmed
Accessories: none
Main specifications: Dimensions W490 (including handle) x H320 x D483 mm, weight 14 kg
The disposal price has been reduced. Member discounts are not applicable. 2023/6/12 sales price 49,800 yen ※1 mono amplifier only. The display lamp visible through the lattice is a transistor mono power amplifier with an indescribable design. As for the sound quality, it is a powerful sound with a sense of overhang while making you feel thick, and the low frequencies are not sluggish, making you listen to a pleasant sound. The exterior is dull all over, scratches on the top plate, etc., and there is a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2023.6.13 Maintained (output relay contact correction input volume disassembly contact correction protection circuit transistor replacement input terminal polish)
Accessories: none
Main specifications: effective output 150 W, input level adjustment, SNR 110 dB, dimensions W436 x H95 x D328 mm, weight 11.5 kg/1 unit
The disposal price has been reduced. Member prices are not applicable. 2024/3/7 sales price 128,000 yen Maintained! A crisp, bright, and sharp sound typical of Marantz from the 1970s. Exactly, it's an American sound on the west coast. The design is also a simple design typical of US Marantz. ※The leg is out of stock. The exterior has dullness and small scratches. Serial 4180 (Yonejima Satoshi)
Maintenance information: 2024.3.7 Maintained (single CH power stage transistor replacement. Screwdriver transistor resistor replacement. Drive Tr Capacitor Replacement Contact polishing, aging test)
Accessories: No accessories
Main specifications: 125W+125W (8Ω) W445 × H170 × D265 mm 14.8 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/2/22 sales price 8,000 yen. Self-made cabinet for DENON DP-3000. The arm was attached to the company's DA-305. When the four-square screw is removed, it is divided into 3 plates, making it easy to perform processing such as drilling. There are scratches, fading, stains on the main body, cracks, repairs, fading, stains, and adhesive tape marks on the dust cover (Kanai Hidetsugu)
Accessories: dust cover
Main specifications: W600 x H112 (H202 with dust cover) x D500 mm 12.6 kg (actual measurement, dust cover included)
The disposal price has been reduced. Member discounts are not applicable. 2024/2/6 sales price 59,800 yen ※1 shelf board is missing and has 3 tiers, and is cheap because there are many scratches. A popular large rack. It is a model that can even adjust the storage capacity and height. It also has high performance as an audio rack, and is made of full-bodied natural wood, with a sturdy structure and interior design. You can see a feeling of use, such as appearance, dullness, small scratches, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: W1230 x H703 x D563 mm Weight approx. 52 kg
※Only 1 bottle is currently sold because it is cheap. Bookshelf speakers made in England. It features compact, tight low frequencies and stretchy mid-high frequencies. There are scratches, threads, and the smell of oil (Daiki Goto)
Maintenance information: 2024.4.10 operation confirmed
Accessories: none
Main specifications: 89dB 6Ω W210 × H380 × D220 mm 5.4 kg
The price has been reduced! 2024/4/5 sales price 500 yen The sound quality of only one 2.0m QED speaker cable feels thick and flexible throughout the entire range. You can use it regardless of genre. The exterior is good with no conspicuous scratches (Tomoho Asae)
Maintenance information: 2024.4.5 continuity confirmed
Accessories: none
The disposal price has been reduced. Member discounts are not applicable. 2023/12/16 sales price 25,000 yen ※1 bottle only. Bass reflex enclosure imitating JBL's mid-size speaker S-99Athena. The lattice grill that symbolizes old JBL is well-made. In addition to being able to see many defects in the exterior and lattice, there is a feeling of use such as dullness, abrasions, small scratches, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: woofer aperture diameter 316 mm, screw pitch (diagonal) 338 mm high range aperture diameter 134 mm, screw pitch (diagonal) 160 mm W610 x H450 x D314 mm 16.5 kg
SAEC long-selling model with a 0.6 m digital cable. 6N ultra-high purity copper with excellent transmission characteristics is used as the conductor material, and transmission loss is reduced with accurate impedance matching (Tamura Eiji)
Maintenance information: 2024.4.4 continuity confirmed
Accessories: none
The disposal price has been reduced. Member discounts are not applicable. 2023/5/5 sales price 9,800 yen. ※1 bottle only. A crossover network with exactly the same structure as the company's X8. This network is recommended when using BB4 with a T350 or 12TRXB. There is a feeling of use such as peeling and scratching on the label (Mizushima Itsuro)
Maintenance information: 2023.5.5 operation confirmed
Accessories: none
Main specifications: crossover frequency 3,500 Hz 8 ohms allowable input 100 W external dimensions W114 x H89 x D92 mm weight 680 g